Series 3 2.25 Diesel 88" Front Leaf Springs
- Thread starter Ric82
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 34,062
- Location
- North Shropshire
I bought mine new in about 1995.. they were about £20 each if i recall
Ric82
Active Member
- Posts
- 93
- Location
- Lincolnshire
I bought the vehicle as someone else's failed project and I have spend slot if time correcting things that just wasn't right mainly bolt just finger tight or things just installed wrong so changing the springs get me back to a known state also it means I get to play on the landrover a bit longer
just a shame it's not the warmest.I see that in post #16 you state that you've ordered new OEM spec springs from Paddocks.I bought the vehicle as someone else's failed project and I have spend slot if time correcting things that just wasn't right mainly bolt just finger tight or things just installed wrong so changing the springs get me back to a known state also it means I get to play on the landrover a bit longer
I've had a few of these, I'm sorry to say that the quality can be variable.
Generally speaking, if they look right when you first fit them, they will be good for the next ten years at least.
If the vehicle don't sit right, take them back straight away.
Paddocks state "UK Made"
But the trade description laws in the UK are notoriously lax in this respect.
I can remember watching a documentary about the UK cutlery trade.
Stainless steel blanks of knives, forks, spoons, etc are imported from the Far East by the container load.
After undergoing a series of intensive automatic polishing operations, they can have "Made in England " stamped on them, and it's all perfectly legal, because of the amount of "work" put into them by the polishing and packing.
Wildefalcon
Well-Known Member
- Posts
- 1,696
When you open clamps use a mapp torch to heat the bent clamp steel or you run the risk of the clamp fracturing.
steve2286w
Well-Known Member
- Posts
- 4,596
- Location
- monkeyangerland
Good tip I didn’t do that 
- Posts
- 34,062
- Location
- North Shropshire
Wildefalcon
Well-Known Member
- Posts
- 1,696
It's a bloody hot blow torch.
- Posts
- 34,062
- Location
- North Shropshire
No such thing anymore apparently but propene seems to be an alternative sometimes sold as "MAPP"
Ric82
Active Member
- Posts
- 93
- Location
- Lincolnshire
Just to give you all an update, my new springs have arrived. Once the weather dries up, I'll get them fitted and report back.
Ric82
Active Member
- Posts
- 93
- Location
- Lincolnshire
Good Afternoon, all
So I got up early this morning before the weather turned and popped on the driver's side front spring.
See attached it's lifted the vehicle about 10/15mm.
I stood the old and new spring next to each over and height wise they was basically the same but the difference I saw was the old spring I could pushed down about 1/2 inch by hand where the new one didn't budge at all. One other thing to note was if I tapped the old spring it sounded hollo where the other sounded more solid metal not looked to see if anything is broken yet.
Update just had to get something out the truck and it feels solid now like there is no give in the spring. I assume after I have changed them both and done a few laps they will bed in abit but concerned that I will end up with them back up against the chassis
What people's thoughts?
Thanks
Richard
So I got up early this morning before the weather turned and popped on the driver's side front spring.
See attached it's lifted the vehicle about 10/15mm.
I stood the old and new spring next to each over and height wise they was basically the same but the difference I saw was the old spring I could pushed down about 1/2 inch by hand where the new one didn't budge at all. One other thing to note was if I tapped the old spring it sounded hollo where the other sounded more solid metal not looked to see if anything is broken yet.
Update just had to get something out the truck and it feels solid now like there is no give in the spring. I assume after I have changed them both and done a few laps they will bed in abit but concerned that I will end up with them back up against the chassis
What people's thoughts?
Thanks
Richard
Attachments
Last edited:
steve2286w
Well-Known Member
- Posts
- 4,596
- Location
- monkeyangerland
Nice one, that angle on the hanger looks more like mine now, be interesting to see if there was a broken one among the leaves
We’re the springs labelled so you could put the correct side on
We’re the springs labelled so you could put the correct side on
Ric82
Active Member
- Posts
- 93
- Location
- Lincolnshire
Yeah they had part numbers on but I also double checked the one with the most camber went on drivers side same as did when I fitted the rear.
Ric
Ric82
Active Member
- Posts
- 93
- Location
- Lincolnshire
Good evening all
So tonight I managed to knock off work early and it wasn't raining so nipped out and swapped the other spring.
Left shackles loose took it for a drive round then parked on nice flat ground check the suspension height and talked it down. it was 114mm from chassis to axle.
The gap between the chassis and spring has closed up a little but at least there is a gap now, I'm not sure why it is like that but assume I just have to live with it.
Rides so much better now as well I can't believe the difference it no longer rolls around the corners.
Thanks
Ric
So tonight I managed to knock off work early and it wasn't raining so nipped out and swapped the other spring.
Left shackles loose took it for a drive round then parked on nice flat ground check the suspension height and talked it down. it was 114mm from chassis to axle.
The gap between the chassis and spring has closed up a little but at least there is a gap now, I'm not sure why it is like that but assume I just have to live with it.
Rides so much better now as well I can't believe the difference it no longer rolls around the corners.
Thanks
Ric
Attachments
steve2286w
Well-Known Member
- Posts
- 4,596
- Location
- monkeyangerland
Nice one, they do rust quite quickly, I wish I’d put some wax oil or similar on mine just after I fitted them, good when you don’t bounce out of seats going over road ramps
- Posts
- 34,062
- Location
- North Shropshire
I found driving faster helped massively.. maybe the tyres deformed more
Ric82
Active Member
- Posts
- 93
- Location
- Lincolnshire
I have lanoguarded them since I took the picture earlier inuse it on all the chassis inside and out and it works bloody brilliantly.
The council have conveniently installed speed bumps all along the road where I live, maybe 200 yards apart.
Plays havoc with series suspension at about 20 -25 mph.
But if you speed up to 40mph (30mph speed limit) it actually takes them better.
And hopefully keeps my springs from seizing with rust
Plays havoc with series suspension at about 20 -25 mph.
But if you speed up to 40mph (30mph speed limit) it actually takes them better.
And hopefully keeps my springs from seizing with rust
