crashbox
Well-Known Member
- Posts
- 12,347
- Location
- In the UK, thankfully.
Wow, I am really enjoying this, keep the pictures going.
1975 series 3 rebuild ongoing (lots of photos)
- Thread starter onecelledcreature
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
onecelledcreature
Active Member
- Posts
- 280
- Location
- Cheshire
cheers mate,
here's a couple of others from the last few weeks
First time on the ramps
Side view. Love having the body back on
Chassis from below
Front end from below
How do i know if the balls need replacing, they're filthy but not worn.
is it a simple job to get them apart and clean? are there many bits that will need replacing inside there?
Land Raver
Well-Known Member
- Posts
- 2,015
- Location
- In the dog house
The UJ's are in the swivels. I would clean them with a degreaser on the outside and look for any pitting in the chrome. If they then still look ok I would drain any old oil from the swivel housing via the little plug at the bottom and refill with some fresh Ep90 or swivel grease. I replaced my swivels earlier this year but ended up having to replace all wheel bearings, axle tube bearings and stub axle carriers. At least a good full days job to do each side for a novice like me. 
Your rebuild is looking fab- keep the pics coming
Your rebuild is looking fab- keep the pics coming
waldershelf
Well-Known Member
- Posts
- 2,397
- Location
- In the hills north west of Sheffield
Nice rebuild. Keep the updates coming we all love a good rebuild thread.
honolulujoe
Well-Known Member
- Posts
- 6,137
- Location
- richmond surrey
wow, superb job, can't believe this is your first one
onecelledcreature
Active Member
- Posts
- 280
- Location
- Cheshire
Not much happened since November, ****ty weather and busy work weeks really kills your enthusiasm for projects like this.
Its been sat under a tarp since mid November, but the sun was out and i wasn't working this weekend so its back on, hopefully to be finished soon
Stripped off the cappings, lights and everything else at the back
Then wirebrushed and etch primed them, and finished with silver paint
got a few other little things done today at well, including some panel repairs where the ally has had some serious contact corrosion. didn't get any photos of those bits
hopefully i should have some real time to get on with this now and get some real work done.
Its been sat under a tarp since mid November, but the sun was out and i wasn't working this weekend so its back on, hopefully to be finished soon
Stripped off the cappings, lights and everything else at the back
Then wirebrushed and etch primed them, and finished with silver paint
got a few other little things done today at well, including some panel repairs where the ally has had some serious contact corrosion. didn't get any photos of those bits
hopefully i should have some real time to get on with this now and get some real work done.
onecelledcreature
Active Member
- Posts
- 280
- Location
- Cheshire
cheers mate, im going off trial and error and calling in favours where i can, getting a lot of inspiration from threads on here though
Last edited:
onecelledcreature
Active Member
- Posts
- 280
- Location
- Cheshire
Looks good, I see you have the same issue with tub corrosion I have.
Also, make sure you update r/serieslandrover
yes, its worse on the front bolts.
I've had a quick go at making a brace for it, not fitted yet. I'm just going to rivet the patch behind the current metal. hopefully when combined with the other cross member attachments either side the weight on it will spread enough for it to hold.
will post some photos when i've done it
also just fitted the new rear light attachments last night, love that look of new parts going on
tom1disco.300
Active Member
- Posts
- 389
- Location
- southwater/horsham westsussex
mate,this is looking realy good,wud love to do this to my 88 diesel,but its my every dayer at the moment,so i cant,but if i have the funds after my rangerover i will deffanantly be doing this to mine,but my chassis is on its last legs,its only half origonal,so only a galvanised would do!! but this is looking realy good,keep the pics coming!! hope she will be kept origonal as u can tho,with a few add on's obviosly!!
onecelledcreature
Active Member
- Posts
- 280
- Location
- Cheshire
Ok bit of work been done this last week
Stripped some of the flaky paint from the wings.
Got some etch prime on
Also fitted the lights to the cappings, not ready to fit the cappings but wanted an idea of how they'd look
love seeing bits go back on, gives a glimpse of progress.
Next started to change brake cylinders so i could finish the back end and get the tub bolted on sometime soon
Finished the rear pipes now, bit rough and wobbly.
most of the work to do at the back is now done
So when some mates were about this weekend started to do some work on the gear box, plan was to take it out and change the clutch over. (this goes way above my actual mechanical knowledge)
Drained the oil, this was all that came out. not healthy at all i assume? big gush of very clear water and a trickle of mixed coloured oil.
the transfer box was much more full and a sort of grey black mix.
Got it lifted
was not as heavy as we were expecting
will be having a good go around this part of the chassis now the box is out.
wasn't planning on having the box out at first so haven't treated the metal i couldn't reach, however the oily grime has protected it pretty well, there's a lot of original paint still there
got the flywheel off too for a good look behind
so some progress, feel a bit in too deep getting into the proper mechanicals, so the haynes and the parts book will be out of the next few days and will hopefully get everything sorted and back together soon.
really need to get the body back together just for the protection, (the tarp keeps blowing off)
bulkhead will be going to the blasters in the next couple of weeks, will also look at getting them to spray it too as i don't have room for that.
Have also picked up a compressor and paint gun too.
will keep updated
Stripped some of the flaky paint from the wings.
Got some etch prime on
Also fitted the lights to the cappings, not ready to fit the cappings but wanted an idea of how they'd look
love seeing bits go back on, gives a glimpse of progress.
Next started to change brake cylinders so i could finish the back end and get the tub bolted on sometime soon
Finished the rear pipes now, bit rough and wobbly.
most of the work to do at the back is now done
So when some mates were about this weekend started to do some work on the gear box, plan was to take it out and change the clutch over. (this goes way above my actual mechanical knowledge)
Drained the oil, this was all that came out. not healthy at all i assume? big gush of very clear water and a trickle of mixed coloured oil.
the transfer box was much more full and a sort of grey black mix.
Got it lifted
was not as heavy as we were expecting
will be having a good go around this part of the chassis now the box is out.
wasn't planning on having the box out at first so haven't treated the metal i couldn't reach, however the oily grime has protected it pretty well, there's a lot of original paint still there
got the flywheel off too for a good look behind
so some progress, feel a bit in too deep getting into the proper mechanicals, so the haynes and the parts book will be out of the next few days and will hopefully get everything sorted and back together soon.
really need to get the body back together just for the protection, (the tarp keeps blowing off)
bulkhead will be going to the blasters in the next couple of weeks, will also look at getting them to spray it too as i don't have room for that.
Have also picked up a compressor and paint gun too.
will keep updated
onecelledcreature
Active Member
- Posts
- 280
- Location
- Cheshire
Ok, a bit more done this weekend
wings and some panels primed up and got some painting done
had a few hours but the rain came while it was still a bit tacky, managed to rush it into shelter just in time
wings and some panels primed up and got some painting done
had a few hours but the rain came while it was still a bit tacky, managed to rush it into shelter just in time
onecelledcreature
Active Member
- Posts
- 280
- Location
- Cheshire
Have you painted the headlight there or was that Ollie? :fighting:
have a guess!
its the old one, left it in cause i couldn't get the plastic surround out, figured the light would protect it
also laziness
Imortalrelic
Member
- Posts
- 47
- Location
- Auckland NewZealand
Excellent! Looks good!
Cant wait untill my attempt in a six months or so
Keep the photos coming
Cant wait untill my attempt in a six months or so
Keep the photos coming
honolulujoe
Well-Known Member
- Posts
- 6,137
- Location
- richmond surrey
love the bits in the greenhouse no room for tomatoes this year
onecelledcreature
Active Member
- Posts
- 280
- Location
- Cheshire
bit more done this last week despite the weather
got the props off to look them over and clean up.
front in good nick, struggled to get the joints out, and separate the two ends
rear was too far gone, dust seal has seized on and grease is grimey and gritty
will replace
Cleaned the yolks and prop ends up
I'm really struggling to fit the new UJs in, haynes manual suggest a gentle tapping which achieves nothing, most guides on the net suggest using a vice or heavy tapping. but the bearing caps are such a tight fit that any movement requires such force that the needles are dislodged instantly.Currently one joint is in but its so tight i'm sure the needles have come away inside. so will re do again.
any advice for this job?
Also this week picked up a tailgate that was on a mates defender when he got it.
some bellend badly fitted a wheel carrier, which with all it's bodges just looks cack.
so i've ripped with straight out and filled the holes in.
New reinforcement bar in place
Holes filled in (sorry bad photo)
and paint on
Got a few moe bits painted while there was a break in the snow
love the look of the doors with the cappings on after painting. fresh paint feels like a massive achievement.
lastly spent a bit of time laying things out at the back so i could drill holes and fill the others before painting
Number plate lamp has a mounting bracket on it. will look for a decent spotlight to put on there
got loads done the last few weeks,
will be looking for a good gap in the weather to get the bulkhead painted and the rear tub.
and at the same time sort out the gearbox in time to fit them in.
Long term plan is a canvas, but can't afford that right now, so i'm currently looking for a cat flap door to use with the tailgate and the hard top.
Lastly anyone know the best colour to paint the hard top? i think limestone will look wrong, and i'm not keen on the single colour look.
would white go with battleship grey?
got the props off to look them over and clean up.
front in good nick, struggled to get the joints out, and separate the two ends
rear was too far gone, dust seal has seized on and grease is grimey and gritty
will replace
Cleaned the yolks and prop ends up
I'm really struggling to fit the new UJs in, haynes manual suggest a gentle tapping which achieves nothing, most guides on the net suggest using a vice or heavy tapping. but the bearing caps are such a tight fit that any movement requires such force that the needles are dislodged instantly.Currently one joint is in but its so tight i'm sure the needles have come away inside. so will re do again.
any advice for this job?
Also this week picked up a tailgate that was on a mates defender when he got it.
some bellend badly fitted a wheel carrier, which with all it's bodges just looks cack.
so i've ripped with straight out and filled the holes in.
New reinforcement bar in place
Holes filled in (sorry bad photo)
and paint on
Got a few moe bits painted while there was a break in the snow
love the look of the doors with the cappings on after painting. fresh paint feels like a massive achievement.
lastly spent a bit of time laying things out at the back so i could drill holes and fill the others before painting
Number plate lamp has a mounting bracket on it. will look for a decent spotlight to put on there
got loads done the last few weeks,
will be looking for a good gap in the weather to get the bulkhead painted and the rear tub.
and at the same time sort out the gearbox in time to fit them in.
Long term plan is a canvas, but can't afford that right now, so i'm currently looking for a cat flap door to use with the tailgate and the hard top.
Lastly anyone know the best colour to paint the hard top? i think limestone will look wrong, and i'm not keen on the single colour look.
would white go with battleship grey?
Last edited:
honolulujoe
Well-Known Member
- Posts
- 6,137
- Location
- richmond surrey
white should be fine imho goes with just about anything
Land Raver
Well-Known Member
- Posts
- 2,015
- Location
- In the dog house
I would go Limestone you mention you're going to have a tilt eventually. If you want to sell the hardtop then Limestone could be more desirable to sell?
Great progress. Nice painting !
Great progress. Nice painting !
