110 Wolf doors, repair, or replace?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Great, that's one more thing out of the way.

Now got a nasty wire chop behind the convoy switch to sort out and I'm no sparks.

Any clues what these wires are, especially the shorted out connector?
Wolf wires.jpeg
 
The 3x brown double bullet females are permanent live / output from the fuse box - but check with your DVM. The green-brown [purple?] link is non-std, what colour wires are on the connector input?

Suggest getting both Haynes and Workshop Manual for wiring diagrams. MOD Landy wiring is not too different from Civvy Landies. All that mud/crud on your wiring will can be cleaned with a good dose of WD40 and a rag

eta: whatever you do don't chop any wires, far better to thoroughly clean and inspect, then work out where the wires go.

note: most MOD Landies have spare brown wires behind the centre dash/rotary light pod - I've used my spares for a cigar lighter, twin USB port and a flexible map reading lamp :)
 
Last edited:
Part of the convoy switch works, part does not. I'll look again when I get home. There is a broken wire in the fuse box, supposedly the passing light and horn feed - does that sound correct?
 
What colour is the broken wire?

Genuine Q...do you have a DVM [digital volt meter] and know how to buzz out wires/electrical ccts for continuity/volts/measure resistance/current? If not, buy a DVM and learn how to do this, it's a much needed skill with car wiring. Really recommend the Haynes car electrical manual

51vQzDEfgAL._SX380_BO1,204,203,200_.jpg


and something like this

51cwPwCYcNL._SY291_BO1,204,203,200_QL40_ML2_.jpg


The best thing with these books is that one can learn each of the techniques live on your Landy without doing much harm. Just don't short out your ignition/starter ccts to ground whilst trying to start the engine as you'll get a big surprise!
 
Haynes manual is now on order.

Is the Workshop manual a single volume? I've seen online downloads in 5 parts and a "Repair" manual is separate again.
 
v8250 said:
What colour is the broken wire?

Genuine Q...do you have a DVM [digital volt meter] and know how to buzz out wires/electrical ccts for continuity/volts/measure resistance/current? If not, buy a DVM and learn how to do this, it's a much needed skill with car wiring. Really recommend the Haynes car electrical manual

51vQzDEfgAL._SX380_BO1,204,203,200_.jpg


and something like this

51cwPwCYcNL._SY291_BO1,204,203,200_QL40_ML2_.jpg


The best thing with these books is that one can learn each of the techniques live on your Landy without doing much harm. Just don't short out your ignition/starter ccts to ground whilst trying to start the engine as you'll get a big surprise!
Click to expand...

I do have a meter, or AVO, as I knew them, so I'll get that Haynes as well.

I opened the fuse box and the broken wire is purple, as per this pic. Where ought that to be attached and is it a bayonet fitting?
Wolf fuse purple wire.jpg
Wolf fuse purple wire.jpg
 
Purple = Horn, Clock, sometimes cigar lighter [this can also be brown], interior light, horn and hazards. Is there a broken purple wire on the output of any of the fuses?

Pls use these as ref'

Defender Wiring diag1.PNG


Defender 1991 to 1994 and 1986 12j engine.png
 
Thank you v8250, I will go and pull the fuse panel and look.

Which colour wire deals with the passing/headlight flash circuit please?
 
Pulled the small fuse holder and there is no obvious missing connection into a fuse, but there are two spliced wires and half of Somalia in there:
Fuses 2.jpeg
Fuses 4.jpeg
Fuses.jpeg
 
That's mess, typical Landy wiring. I'd be inclined to thoroughly clean and inspect all wiring, and then trace and note all the wires to their points of use...then replace the bodged wiring with fresh correctly coloured wires.

Welcome to MOD Land Rovers...;)
 
v8250 said:
What colour is the broken wire?

Genuine Q...do you have a DVM [digital volt meter] and know how to buzz out wires/electrical ccts for continuity/volts/measure resistance/current? If not, buy a DVM and learn how to do this, it's a much needed skill with car wiring. Really recommend the Haynes car electrical manual

51vQzDEfgAL._SX380_BO1,204,203,200_.jpg


and something like this

51cwPwCYcNL._SY291_BO1,204,203,200_QL40_ML2_.jpg


The best thing with these books is that one can learn each of the techniques live on your Landy without doing much harm. Just don't short out your ignition/starter ccts to ground whilst trying to start the engine as you'll get a big surprise!
Click to expand...

Found this one, slightly different title: https://www.ebay.co.uk/itm/174783345901?hash=item28b1e634ed:g:CXYAAOSwdE9gr3q6
 
You must log in or register to reply here.

Similar threads

O
New to Landy zone & recently purchased 1996 Defender 110 300 TDI
Replies
2
Views
173
brianp38dse
brianp38dse
MacStu
Wolf style rim retrofit to 1983 110
2 3
Replies
50
Views
1K
miktdish
miktdish
Brenda__the__Defender
Advice on Tyre choice please!
Replies
14
Views
1K
Brenda__the__Defender
Brenda__the__Defender
Jbdisco
110 roof cracks
Replies
10
Views
1K
dag019
dag019
T
Central locking not working on all doors except drivers
Replies
6
Views
803
Stanleysteamer
Stanleysteamer
Back
Top