Search results

Passed mot this morning. A full year of trouble free motoring ahead

Thanks, that's very kind of you. I've ordered one off ebay but it's not due to arrive until Saturday and I'm a bit nervous that it will also be fried, so come Saturday I may need your offer. Can I arrange to get it collected from you? If I don't need it and yours works ok, why don't you stick it...

Actually, when I replaced the one on the other side, the hardened washer was fitted between the ball and the mounting bracket, not between the nut and the bracket. I've swopped the previous one also

Burned reflector bowl And yes, that is my thumb

Bad news people My 2002 L322 failed mot on saturday The failure sheet says "reduced light intensity" The xenon lamp lamp is striking ok, and the full beam solenoid is working ok. The thing I have doubt about is the self levelling stepper motor. I've jacked up the front of the car but tge motor...

Sorted this (I think), the plug into the RH rear height sensor wasn't properly seated Also found the there was some corrosion in the ABS connector (C0506) and that pin 11 (steering angle sensor) was bent flat. I've no idea if that contributed or not, and I've no idea how the thing worked at all...

Thank goodness, because that's exactly where I put it. Strange that the manual says 'be careful to put it in the right place', but doesnt say where that place is That sounds familiar somehow

Evening all 2002 L322 rear suspension anti-roll bar links. Do any of you knowlegeable people know where the hardened washer goes on the strut spring seat end of the rear anti-roll bar link? Does it a) go under the nut, or b) under the flat on the ball end of the link, or c) does it matter? Thanks

Thanks Virtus1 - very useful, at least it's told me that while I'm getting an air suspension inactive fault on my 2002 L322, the problem could actually be the ABS or short harness (whatever that is) I replaced the LH rear height sensor yesterday, but nothing has changed. The IID tools allows me...

So, i fitted the new height sensor but the fault won't reset - I'm getting a CAN error Here's the full list - any thoughts? Model L322 - Range Rover 2002 Vehicle scanned on 27 Feb 2021 13:24:10 IIDControl 2.9.9.9 Build 74 Android - IIDTool BT V4.0 B2742 ABS-Brake Module 0x8A Air suspension...

Apparently I need a new drivers side height sensor Does anyone know the part number for a RR with Halogen headlights and the best plave to get one? Is the end of it that attaches to the lower arm supposed to be free enough to allow it to able to rotate?

Gap iid BT it is

Anyone have any views on iCarsoft LR V2? I'm afraid I don't currently have £600 (plus Brexit import tax to Northern Ireland) to lash out on nanocom. Would I be better saving up for it? What doesn't iCarsoft LR V2 do?

Thanks for your response. The 'normal ride height' and 'lock' lights come on for maybe 5 sec and then go out and stay out until the ignition is switched off and then on again. I'm in Ards in Northern Ireland

What a relief. I've had my 2002 3 litre tdi RR for almost 2 months and I was beginning to worry that I'd never have an 'inactive suspension' fault. What a relief when it happened today. I was beginning to think that I'd always be a virgin. The lights are all off on the suspension panel but it...

These guys have a great repuation https://www.blrcvehiclespecialist.co.uk/

The button seems to work ok but I dont know if HDC itself vunctions or not

No, if I select when in drive it doesn't do anything and doesn't say to select neutral. I've also tried it in neutral with my foot on the brake and it does absolutely nothing. No lights no sounds no nothing.

Thanks The wiring diagram shows P145 is a fuse holder rated 50A Presume it's somewhere near the battery. Is that the one?

I think the correct word is "bugger"