Search results

Okay, after a couple of hours of checking continuity on each pin, checking earths and so on... It was the pressure switch. Took about 20 minutes to swap out, problem solved.

There's a rubber seal around the connector end, and the rest of the enclosure is one piece of metal...wouldn't be surprised if it's completely airtight once assembled

Before I start, I know these engines are renowned for leaking oil, so I'm not panicking, just after some advice on whether it's an immediate issue or something I can sort over summer when it's easier to get time! So my engine has started leaking oil, it goes from around the full mark on the...

And in case anyone was wondering what the ECU looks like Naked, here's some saucy pictures (NFSW): https://photos.app.goo.gl/MkLAe45PReauwRz57

For anyone else contemplating this you can't start at the bottom like you would if the door was open as there's no space to get leverage from underneath. I started at the top, there's enough give in the door card to 'persuade' the metal bit to come over the lip of the door, then you can push the...

Update: You can remove the rear door card with the door shut, with a little persuasion. Removing the door card and slicing through the foam allows access to the cable for the latch motor. Applying 12v to the wires did nothing for either polarity. Breaking the motor off the latch allows you...

That's what she said.

Engine bay: https://photos.app.goo.gl/ZzM4abKKDiU1TDPX7

That plug has a metal clip on it which looks like a bit of a pain to get at since the cables for my LPG installation run over the ABS pump....so I'll give it a go once I have a few hours, in daylight with the car on a drive.

Just rich enough to drive a 20 year old mobile oil leak :D

Yeah, I don't have a lot of free time, or access to a drive / garage so the only way I can do anything on the car is by arranging an afternoon in advance to go over to my dad's and put it on his drive. The upshot of that is I'd rather spend £70 and have more chance of sorting the issue in one...

Sure, I'll get one in the morning, bit dark out there at the moment :D

My LPG setup has 2 vaporisers, one each side of the engine ...no idea why, it was like that when I bought the car. I'll take another look at the pipework, and see if I can work out exactly where the leak is. Thanks all!

Hmm, it does have LPG, but I've been round all the pipes and they all seem solid. Does the heater matrix have coolant circulating through it when it's not heating anything? I've only noticed the leak since the cold weather has kicked in, but that might just be coincidence

Hi all, to add on to my ABS pressure switch failing and my rear door latch failing I now suspect my O-rings are on their way out due to a slow coolant leak and a wet carpet on the drivers (right hand) side. However, I notice when I remove the right hand panel on my centre console someone has...

Cheapest I can find the Saab equivalent for is £150ish: https://www.saabits.com/all/saab-900-9000-abs-brake-pressure-sensor?cPath=73_110_117&zenid=hjlkapuel53lc1k7sgkui5j0k5 I picked up a used pump & switch for £70, as long as the switch works I got a spare pump out of the deal.

Okay, according to the diagnostics I have a 'pump pressure switch fault' So, is that this doohickey? https://www.ebay.co.uk/itm/Range-Rover-P38-4-0-4-6-ABS-pressure-monitor-switch-1995-1996-1997-1998-2002/264104988645 Anything I should do before assuming it's faulty and replacing it?

Bit more info in case anyone is curious.... The delay relay picks up the 'ready to send' pulse from a serial cable plugged into the OBD connector (pin 1 OBD -> pin 3 delay relay) which causes the ECU to power cycle during the serial initialisation, which puts it into 'diagnostic mode'. If you...

I've literally just had this with mine! Thanks to the fine folk on this forum I tracked it down. First off take the air con inlet filter off the left hand side (lift the bonnet, the filter is under a cover held on with 2 screws just under the windscreen). Pull the filter out. If it's wet at the...

@martyuk where's the best / easiest place to pick up the pink & orange wires so I can apply 12v to them? Can I just unplug at the becm end and try there or is there somewhere closer to the latch end I can get them without taking loads of trim apart?