Hicap phill's latest activity

cylinders 1 and 2 share a port as do 3 and 4 so it doesn't make sense If two and three are black then I can't think of a cure off hand Maybe a plug problem, clean em off and swap them around see what happens

Have you turned the knob on the relay till the trailer light on dash flashes once? does the turn signal work on the dash?

it’s not an adjustable relay.. I’ve got one coming today. 1991.. 200tdi

Still working through my (getting shorter) list of family and mates who want a ride in the 101. My nephew called in this morning. I was pre-warned so was checking the tyre pressures on it and the BM. The back two go down a few psi over a couple...

Have you twisted the knob on the led relay? Also what year is the motor?

Series windscreen wiper wheel(incomplete) Puller of some description Wiper motor Unknown parts

Are you using the chassis or reg number to find the part? You will need to get that front pulley off. (Allen key in middle & ring spanner,spanner may need a shock knock to start with)

Tying it back in now on N/S

Well that is the last of the ABS saga at least for a while! New CV & Shaft. Lights came back... 🤷‍♂️ New sensor in lights gone! Funny how the sensor lasted a year to the day! But its a 2 year warranty so will be going back to Island4x4 for a...

I’ve done the front pillars. You need to drill out the spot welds to get the old part off. Replacements are available from YRM. They recommend installing these using structural adhesive, obviously as most of us don’t have access to an aluminum...

Have you tried to drive it in reverse for a short distance to loose any transmission wind up?

You need a new alternator. The bearings & bushes will be U/S in the 1 you have

Well, I tried the connector block with the multimeter and all shows well/ Then I put the light back on and the low beam failed; I then tried linking the lights terminals swapped over and back again and all's well. This shws the light is OK, but...

@Anaconda - actually, you were right! Your train of thought got me thinking, and I removed the spacer washers on the outer rear bolt, and it not all works fine :) . All it needed was to look at it with a fresh pair of eyes, so thanks very much much!

Do you mean a restoration? If yes then I guess someone better point out it will cost way more than it will ever be worth if you are paying someone.

Honestly I don't think this one leaks at all! I know its practically unheard of with any Land Rover, never mind one that's almost 40! There could be a small leak somewhere I haven't spotted yet, but I got way more on the ground trying to drain...

tbh, I'm amazed how anyone can buy a vehicle and know nothing about it. Missing front prop? Sounds like an utter bodge job tbh. If you knew all the issues before your purchased and how to fix them, then maybe it could represent a bargain. I truly...

Parents decided yellow Cotswold chipping not a good choice for a drive & my landrover ;)

I usually know if the cats been under the landy (cleaning the underneath) :D. Oh and a gravel drive is the best choice 🤔 J

Got an oil pump for the bonneville engine I am rebuilding, off the bay. An original item, cost 5 sovs. Compared to unbranded repros at 70 sovs or branded for 120+ sovs. Modern ones made with brass bodies, originals in bronze. Checked with a...

Afternoon folks :). Well Air BnB are us, yesterday. Flyin use the facilities have breakfast and leave:p. Its Stork (big chicken)time:p We have had a few late arrivals today as it started to be drizzly which is not helpful for the flying, so we...

When you park it up after a long drive see how much oil is on the floor.the next day Most of these leak more oil than they burn.

Update for anyone interested: So I worked out with some testing with a new temp sender (PRC2505) and taking the gauge out to test separately that there was an earthing issue with the gauge. Connected up on my bench to a power supply and the...

For big trips. Few bits of straight pipe(various sizes(slide in each other to save space) Straight metal joiners for pipes electric fuel pump 2xujs(make sure they fit front rear props) Diesel filter That’s about it… all other stuff I could...

Wheel spinning is a necessity to check the, erm, diffs, erm, for the MOT? 🤣

Ah.. I hadn’t noticed that, to be honest I wouldn’t fancy turning this over by hand you’d certainly break a wrist trying

Ooo the good old starter handle hole….

It's more likely to be that the swivel ball will be damaged (worn, pitted etc) which in turn wears the seal. To get everything back to 100% i'd reccommend that you change the whole lot, bearings, seals everything. If you have any sort of lift...

An older style mechanic told me years ago to make sure to pack the spring channel with grease before assembling to protect the spring from water