Grrrrrr's latest activity

Do remember to not take the nut all the way off when you tug and yank at the wheel to get it of as trips to the dentist are eggspensive, or you could take it off and video it for us all to laugh at:vb-biggrin:

Hardest part is getting the damn heatshield bolts off. That and that manifold bolt near the steering knuckle.

V8 almost certainly head gasket.

Think the interior lights are driven direct by BECM so any short will burn out the track on the BECM board.

Hi Grrr! it's true yours is also one of the first but I remember reading that apart from updated electronics, you have a BeCM V36 or 37, so you will also have a more recent ECM than mine. There's a post talking about this, if I find it I'll post it

at post #124 Wammers says: "Nanocom info does say later ECU versions had trimmable values. Maybe the early ones don't need the numbers. But not entirely sure. As said the 97 one didn't have them but I loaded them. But it was a bit of a mishmash...

Post in thread 'Reverse lamp, electrickery knowledgeable peeps, what do you think?' https://www.landyzone.co.uk/land-rover/reverse-lamp-electrickery-knowledgeable-peeps-what-do-you-think.396931/post-5801790

Proflow picture shows a metal impeller....? Might be worth a check though. https://www.island-4x4.co.uk/water-pump-v8-1994-on-proflow-stc4378.html I fitted Airtex last time I did mine.

Mine's an early one. Sure I put the values in a post somewhere and possibly an EDC trace from the Nanocom if he wants to compare the values. Might have called it something like EDCfuelling.xlsb Mine's Late EDC in the settings but as far as I...

The bacteria burning can cause white smoke and the sludge gums everything up, used to see it quite a lot on sailing boat auxiliary engines. It can be very difficult to get the tank clean, had to steam clean them in the past and flush the...

I'd leave that setting at 128 rpm. Adjust idle on pump top to 750 rpm. Lift sensor rpm will follow crank. You'll see them diverge as you accelerate or drop off the throttle. White smoke sounds like too much diesel going through. Air temp will...

Yeah Airtex Mahle also has one that looks quite good, i have one in stock but havent fitted it to an engine yet.

Later v8 with the Thor engine. Anyone know who the original manufacturer was? Is it like the diesel and there's a metal impellar version that is preferred over the original? Recommendations?!

Washed it. 3 attempts required, the last one using neat detergent. Tried to fix the crack in the windscreen but is is too big. Even with the glorious sunshine today it struggled to cure. Also noticed my rear diff is leaking at the seal with the...

Instead of ambulance chasers the new(ish) thing is recovery trucks being L322 chasers

That's because they knew L322 owners would have a Recovery truck following them at all times :)

Work in progress:)

I think Land Cruiser reliability went down shortly after they started fitting air suspension to them! Lexus are reasonably priced second hand. Not sure what they're rated at for towing. Possibly limited by no low range. Never seen one with a...

If that black wire isn't tied up properly it can foul on the window mechanism and break inside. All 3 microswitches need to be working for the EKA input. Boot grounds through the centre one. There's a test sheet on here somewhere.

Given that it's a 1995 car, and might have an earlier BECM, it's probably worth trying Kieth's settings. Disable both Immo & EKA using diagnostic, and then make sure you successfully write settings. Then lock & unlock the car using the FOB...

Sadly the brand name on the part or box means little these days, there is so much fake stuff about.

Been driving around with no warnings which has spooked me. Heavy rain yesterday so flooding yesterday and today. Road closed due to flooding but just set to wading height, opened the window to check the depth and just eased through. Pretty much...

Odd, Range Rovers used to come equipped with a rather decent bottle-jack.

I've been thinking.. as you do.. we think of cheap parts that don't last long as false economy.. but when you add it up using man math.. it's not been on long enough to seize up so easier to replace 🤔

That sounds very cheap.

Around 90€ my mate 🤔

I got one of these if it’s any good Kerm. Still got full set of P38 front ball joints in the freezer too.

Maybe it would float if you pumped them up 🤔. Asking for a friend:p. J

The P38 often does more than the owner is willing to try, As does the L322. They are pretty capable, when they work:oops:. Dont worry the ground will turn slimey and the fender will get its camo back :D. J

We could try doing one old one each ??