mick 1986
Well-Known Member
Yeah I will do mate, but it's just a rectangle at the minute. I have one from on my trailer yesterday. Here's that one for now.
Yeah I will do mate, but it's just a rectangle at the minute. I have one from on my trailer yesterday. Here's that one for now.
baptista
Active Member
still very "boxy", looking forward to see how it evolves
DML
New Member
Solved my new found leaking 3 door boot.
New to the LR ownership and after reading many posts about a leaking cubby box I thought I better check mine.. yeah it was soaked ! pulled the carpet out and that was also full of water so thats now out to dry.. found the leak to be coming from the bottom corners of the window sealer with the right hand side the worst.
I solved the leak by filling the seal with shreading plastic bags to make it more harder and closer seal. Photos are attached to show what bits I mean and how it looked afterwards. Tested with the hose a few times and just cleaned the car and not a drop of water inside. .. FIXED !
Drew
New to the LR ownership and after reading many posts about a leaking cubby box I thought I better check mine.. yeah it was soaked ! pulled the carpet out and that was also full of water so thats now out to dry.. found the leak to be coming from the bottom corners of the window sealer with the right hand side the worst.
I solved the leak by filling the seal with shreading plastic bags to make it more harder and closer seal. Photos are attached to show what bits I mean and how it looked afterwards. Tested with the hose a few times and just cleaned the car and not a drop of water inside. .. FIXED !
Drew
Attachments
I got the AA to transport my Freelander back to the garage I bought it from two weeks ago. The clutch master cylinder needs to be replaced and the handbrake seems to be binding after it's released. Oh, the HDC switch seems faulty, the wipers stopped working, the horn buttons on steering wheel don't work. Thankfully it's still under 3 month warranty.
DD3
New Member
Good for you - get them to sort it! I seriously considered re fitting prop shaft, flushed with success of drive spigot now back in IRD. Anyhow, mild enuf for such an adventure but looked like it would piz down any minute - then it didn't. Ho Hum! Maybe tomorrow.
chrish2012
Member
Changed the VCU and bearings, many thanks to Hippo for his guide, I now feel a lot more confident, I was going to change the oil in the IRD but gave up due to the rain and wind, oil change can wait until tomorrow
DD3
New Member
Make sure you have undone the filler bolt b4 you undoes the drain plug!
chrish2012
Member
Thanks for the advice -only started using the forum since Dec 2012 - but the help and advice from you guys is priceless - THANKS
DD3
New Member
That's OK - its just one o them rules!
The filler can be a fecker to undo, best from underneath with a longish extension bar and decent 19mm (iirc) socket.
sparkysbandit
Active Member
well this was yesterday really...
well er in doors like dancing on ice...i like fekin about in the snow
well er in doors like dancing on ice...i like fekin about in the snow
sijwhite
Active Member
well this was yesterday really...
well er in doors like dancing on ice...i like fekin about in the snow
So was this...
Attachments
DD3
New Member
Good to hear!!
I have now restored 4 wheel drive to the old girl, after much swearing. Went fer a quick spin around the block and all seems fine. Bet it wont snow in these parts again for years - actually, hope it doesn't cos I'm a bit of a BOF and I hate the fecking stuff!!
Dougden
Active Member
well this was yesterday really...
well er in doors like dancing on ice...i like fekin about in the snow
Never been a fan of private plates, but that is a good 'un
sparkysbandit
Active Member
sparkysbandit
Active Member
Never been a fan of private plates, but that is a good 'un
cheers
it was for my 40th birthday (some time ago) i had it on my 1200 bandit
then on my 900 ninja streetfighter
it turned a lot of heads when it was on my bike
