teddyshooter · Sep 27, 2014

Are they wired or battery pack ones?
If they are wired, did you fit yourself?
If yes, what wires did you tap in the door for the feed please?

Barry6690 · Sep 27, 2014

Replaced OSF brake sensor, 3 amigos and handbrake warning light now extinguish on delay after the ignition is switched on, But, the handbrake warning light does not come on now with the handbrake applied

Diesel Do · Sep 28, 2014

Put some new number plates on

thequeenscheese · Sep 28, 2014

Drove home from the garage with no diff as couldn't find a prop bearing in time the back end started to steer all by itself not far from home just pulled into the car park at home and bits came a falling off I'm guessing the hub or bearings destroyed itself..
Will need to take it to bits tomorrow and be having a looksee

Diesel Do · Sep 28, 2014

thequeenscheese said:
Drove home from the garage with no diff as couldn't find a prop bearing in time the back end started to steer all by itself not far from home just pulled into the car park at home and bits came a falling off I'm guessing the hub or bearings destroyed itself..
Will need to take it to bits tomorrow and be having a looksee

Did you leave the driveshafts out? If you did the cv joint holds the wheel bearing together!

thequeenscheese · Sep 28, 2014

Yep no drive shafts in at the min, this is part of what ever fallen off..

GrumpyGel · Sep 28, 2014

:doh:

NeilTD4 · Sep 28, 2014

Yesterday, I found something nasty in the woodshed…

Dangermike · Sep 28, 2014

Was looking under car this morning and noticed this ....

ImageUploadedByTapatalk1411906548.234557.jpg

does this look like a gearbox oil leak to you?
If so I hope it's not too hard to sort

Diesel Do · Sep 28, 2014

thequeenscheese said:
Yep no drive shafts in at the min, this is part of what ever fallen off..

That's the wheel bearing fallen apart. Are you trying to kill yourself?

roccotune · Sep 28, 2014

New rear shocks (ball ache as good old LR decided that when changing the rear shocks it would be a good time to split the brake pipes where they meet the flexi! Then of course the bleed nipple was a pain!). Also fitted a new wiper motor and checked air in tyres

freelander1958 · Sep 28, 2014

I cleaned it ,, got plastic trim back to original colour cleaned underneath as well 3 hours then my other half cleaned inside ,then decided she wants to drive it to work and not her car

:car::car: I just put petrol in it too

thizzlemania91 · Sep 29, 2014

Changed trans fluid and engine fluid. Trying to change transfer box fluid but have no clue how to get that filler plug out

Joshrob1 · Sep 30, 2014

I did my first ever brake pad change today and it couldn't have gone any better :clap2:

I also resprayed my spare wheel/brake light housing, really pleased with result. Have attached a pic:

Trefor · Sep 30, 2014

My TD5 Disco has no cat as it was built for export but always passes its emission test on the MOT without any concessions being made.

SES88 · Sep 30, 2014

Trefor said:
My TD5 Disco has no cat as it was built for export but always passes its emission test on the MOT without any concessions being made.

The early TD5's don't need a cat anyway

htr · Oct 1, 2014

Cleaned and painted drums.
From this

to this

Dangermike · Oct 1, 2014

htr said:
Cleaned and painted drums.
From this
to this

That looks really good! Hanmerite? Spray or brush?
I did this once on an old car but after that the brakes started sounding Grindy

htr · Oct 1, 2014

wire buffed and degreased then Spray on caliper paint.

vilguy · Oct 1, 2014

i repaired my rover ron synergy tuning box after i had a slight whoops and shortcircuited it...

working again now

New Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Active Member

Active Member

Well-Known Member

New Member

Active Member

Active Member

New Member

Attachments

Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Do'er of stuff and the like

Similar threads