Rubberknees said:
Is it really safe to do so or should you go for new or proper welding
Click to expand...
Because of where it is, i don't think welding world work to if i could find someone willing to try.
It holds the dash and lights from wiggling around, if it glues that i can hang off it then will be fine it's not structural to the integrity of the main frame or engine etc.
It's done now!! Though the 2 part epoxy was hard to mix!! Both different consistencies

We shall see this time tomorrow!! Or i might give it to the weekend before i heave on it
 
kermit_rr said:
Because of where it is, i don't think welding world work to if i could find someone willing to try.
It holds the dash and lights from wiggling around, if it glues that i can hang off it then will be fine it's not structural to the integrity of the main frame or engine etc.
It's done now!! Though the 2 part epoxy was hard to mix!! Both different consistencies

We shall see this time tomorrow!! Or i might give it to the weekend before i heave on it
Click to expand...
Don't take any chances pal. Your too precious to leave us
 
rich28uk said:
Looking at the rear facing pic has your side step started to stop from the B pillar and back? Mine have on both sides, box frame underneath has corroded leaving hardly no strength from B pillar and back, going to remove mine and replace the front mud flaps to ones without a step receiver in them.
Click to expand...
Yeah drivers side has passanger side hasn't, if i didn't have the mudflaps with the shape of the step on they'd have been removed by now, i think the side steps aren't the prettiest of things, my old one survived 3 days with chrome bars and they got chopped off
 
Last edited:
Fixed the rear wiper motor for the 3rd time then fitted a proper washer jet.

upload_2023-1-29_22-47-35.png


extended pipe and new hole

upload_2023-1-29_22-48-37.png


upload_2023-1-29_22-49-31.png



new jet in 3d printed housing

upload_2023-1-29_22-50-12.png



upload_2023-1-29_22-50-46.png
 
stustrong said:
Yeah drivers side has passanger side hasn't, if i didn't have the mudflaps with the shape of the step on they'd have been removed by now, i think the side steps aren't the prettiest of things, my old one survived 3 days with chrome bars and they got chopped off
Click to expand...

That’s why iv still got mine on, waiting till free day and decent weather then fit new front mudflats. Managed to find a old new stock of genuine LR ones poor design on them really, no support after B pillar yet that’s where all the weight and leverage is after there.
 
Had to convert my P38 to RWD, UJ failed on me, luckily caught it before it has done any damage to the prop. Looks like the grease has been washed out. Which is weird because it is the tbox front output UJ. New UJ and fresh grease should arrive later this week. I am guessing my open for 10+ years tub could be dead, so going to regrease all the UJs with fresh. Hopefully it doesn't snow between now and then.
 
Bix said:
Had to convert my P38 to RWD, UJ failed on me, luckily caught it before it has done any damage to the prop. Looks like the grease has been washed out. Which is weird because it is the tbox front output UJ. New UJ and fresh grease should arrive later this week. I am guessing my open for 10+ years tub could be dead, so going to regrease all the UJs with fresh. Hopefully it doesn't snow between now and then.
Click to expand...

Are you all fixed up now?
 
You must log in or register to reply here.

Similar threads

A
Range Rover L322 - not turning over
Replies
12
Views
2K
gold rover
gold rover
B
L320 range rover sport 3.0 tdv6 loosing power steering fluid
Replies
3
Views
533
Mark Piercy
Mark Piercy
F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
1K
Grrrrrr
Grrrrrr
T
Non start
Replies
3
Views
717
Datatek
Datatek
T
Fan Clutch??
Replies
14
Views
799
Grrrrrr
Grrrrrr