KISSMYAURA · Aug 26, 2019

Next ,
Swivels
Brake lines
HD Clutch
Rear Drive shaft conversion.
Then enough, onto another project....

KISSMYAURA · Sep 16, 2019

Fitted my flush mount LED reversing lights.

dieseldog69 · Sep 17, 2019

KISSMYAURA said:
Fitted my flush mount LED reversing lights.

View attachment 189748
View attachment 189746 View attachment 189747

Any shots from the dark and dreary night time? Obviously not near any doggin spots but somewhere that we can see how bright they are in the dark

KISSMYAURA · Sep 22, 2019

dieseldog69 said:
Any shots from the dark and dreary night time? Obviously not near any doggin spots but somewhere that we can see how bright they are in the dark

will do!

KISSMYAURA · Sep 22, 2019

Been Sailing! right through my MOT no Advisories and emissions of 0.68 K(1/m) /Smoke temp Min 22 max 25

Not bad for 116K TD5

raywin · Sep 23, 2019

KISSMYAURA said:
Been Sailing! right through my MOT no Advisories and emissions of 0.68 K(1/m) /Smoke temp Min 22 max 25

Not bad for 116K TD5

That's great news, well done. Wish I could get my emission down that low, injectors are my next focus.

KISSMYAURA · Sep 23, 2019

raywin said:
That's great news, well done. Wish I could get my emission down that low, injectors are my next focus.

Engine oil change every 6 to 8K, 30 min run before MOT.
Been using this for 15 years, we have 5 diesel engines including a generator, its use in all.

raywin · Sep 24, 2019

KISSMYAURA said:
Engine oil change every 6 to 8K, 30 min run before MOT.
Been using this for 15 years, we have 5 diesel engines including a generator, its use in all.

View attachment 190352

Ordered some.
Mine looked fine in cylinders 2, 3, 4 but 1 and 5 were very sooty, thinking of sending those injectors to be tested.

KISSMYAURA · Sep 26, 2019

raywin said:
Ordered some.
Mine looked fine in cylinders 2, 3, 4 but 1 and 5 were very sooty, thinking of sending those injectors to be tested.

wait till 1/4 in tank, give it third of bottle, blat along steady at 50 for around 30/40 mins do this a few times and you will see a difference

KISSMYAURA · Nov 14, 2019

Ever decided to do one job and then suffered from the 'might as well do the XXX while i'm there" AKA Triggers Broom syndrome?
What started as swivels is now,swiv housing, stub axles, wheel bearings, shields, CV, etc entire hubs ends on both sides, then season with Timkens and Corteco all round of course.

Stonechipped the brake mud shields etc.

And why the fook not eh?

KISSMYAURA · Nov 15, 2019

Finally found a parts tracking solution and use for all the blue bags!

KISSMYAURA · Nov 23, 2019

Stub Axle Prep:

Seating the Bronze Bush, CV oil / grease Seal and the Roller Bearing (Greased with JCB Blue)

View attachment 194783

View attachment 194787

KISSMYAURA · Apr 10, 2020

Front Swivels, Stub Axle's CV's, Drive Shafts, Wheel Bearings the usual from end refurb...only been putting it off since Nov, as I have been building a music / rehearsal studio at home.

So grabbed some cider, flicked on the A Team sound track and went at it.......

KISSMYAURA · Apr 10, 2020

LH DRIVESHAT!
I may.....just may mind..... have been a bit teeny weeny bit heavy handed when gently teasing / tapping it out ( with a club hammer, red face and a bit of colourful language)

Just as well I have a new HD one...

raywin · Apr 10, 2020

KISSMYAURA said:
LH DRIVESHAT!
I may.....just may mind..... have been a bit teeny weeny bit heavy handed when gently teasing / tapping it out ( with a club hammer, red face and a bit of colourful language)

Just as well I have a new HD one...

View attachment 205226 View attachment 205227 View attachment 205228

Oops oh bugger

Kev12 · Apr 10, 2020

KISSMYAURA said:
LH DRIVESHAT!
I may.....just may mind..... have been a bit teeny weeny bit heavy handed when gently teasing / tapping it out ( with a club hammer, red face and a bit of colourful language)

Just as well I have a new HD one...

View attachment 205226 View attachment 205227 View attachment 205228

Never mind that....

Those sandals

windy81 · Apr 10, 2020

really like the flush mounted reversing lights. Mint!

KISSMYAURA · Apr 10, 2020

Kev12 said:
Never mind that....

Those sandals

they have flesh coloured steel toecaps

Kev12 · Apr 11, 2020

KISSMYAURA said:
they have flesh coloured steel toecaps

It wasnt a safety concern

KISSMYAURA · Apr 11, 2020

Chopped up old Swivel to make a bench mount. Its V tough and about 5-8mm thick, but so much better making up new one on the bench

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads