cornishboater
Well-Known Member
That would make for some wading KeithWell 470 inches for standard ride height would seem to be unlikely
feyniriel
Active Member
Attachments
Those front target heights nee to be within +/- 2 of each other. When below 1mph, the EAS opens the two front valves only, to level the front axle. With unbalanced front Target Heights, the system will cycle between moving to target, and leveling the front.
Also it would be better to get the values with a door open, so it's at standard height, (not levelling).
It needs calibrating.
Also it would be better to get the values with a door open, so it's at standard height, (not levelling).
It needs calibrating.
feyniriel
Active Member
Gotcha.. so how should I calibrate it?
Two options. In both cases, you manually adjust the corners to correct height, and then save the values from the height sensors into the ECU. Start with High Mode. Then do Standard, Motorway & Access in order.
1) Use the measurements above & a tape measure.
2) Use blocks between chassis & axles ( or )
There's plenty of posts on this forum about it.
1) Use the measurements above & a tape measure.
2) Use blocks between chassis & axles ( or )
There's plenty of posts on this forum about it.
Also, your values above look like the car is rather low, or at Access height.
Standard is usually similar to this:
Datatek
Well-Known Member
The numbers your experts are talking about are the bit counts shown in diagnostics, The measurements wheel centre to wheel arch are millimeters
All P38 differ slightly - there is no mm to bitcount reference.
To calibrate, you manually set the car height (either with blocks or measurements), and then program that value into the EAS ECU as the target. Then in normal operation the ECU adjusts to that particular height, until the target is reached.
The actual bitcount depends on where you set it during calibration, but must be within the following range for each height, or the ECU will reject it.
To calibrate, you manually set the car height (either with blocks or measurements), and then program that value into the EAS ECU as the target. Then in normal operation the ECU adjusts to that particular height, until the target is reached.
The actual bitcount depends on where you set it during calibration, but must be within the following range for each height, or the ECU will reject it.
You are correct. There's a bit count from 0 to 255.
There are default values for each height setting somewhere on this site. After that I find the calibration blocks easiest to grab the correct values. Again, the dimensions of the blocks are on here somewhere, probably in the late Wammers How To in the Technical Section.
Datatek
Well-Known Member
A measuring stick is quicker and easier than blocks.
feyniriel
Active Member
How does the measuring stick method work?
feyniriel
Active Member
Thanks for the info! I see in the videos they're using some kind of a computer program. I have a Nanocom, will I be able to program the new heights with it, without a computer?
Yes Nanocom can save the height values. There's several threads on this forum showing how to calibrate the heights. There's also a few YouTube videos as well.
Datatek
Well-Known Member
Yes an air compressor is needed to lift the air suspension, the car is fitted with one, first job is to make sure that the cars compressor works and is making good pressure.
feyniriel
Active Member
So I can use the Nanocom to lift the car with its air compressor, so I could fit the blocks? Or I was wondering if I needed a workshop air compressor. Sorry for the dumb questions, my husband has given up on trying to problem solve my car so it's up to me with my little mechanical knowledge to find answers online.
Datatek
Well-Known Member
With Nanocom, you can send the suspension to any height. You will need the engine running when you do the calibration. For the measuring stick a I use a piece of alloy but wood will do, stand the stick on the ground, (must be level ground, put a mark at the wheel center, from that mark measure and mark the 4 heights that have to be calibrated. The measurements have been posted many times, if you cannot find them I will post them again this evening when I'm in the office.
