eprothe

eprothe

Member
Hello,

I'm posting this here, because I can't think where else to post it, to be quite honest.

I've just come from under my 110, where I'd intended to grease the propshafts and whatever else presented an accessible grease nipple. I had to give up, though, as my grease gun wouldn't pressurise.

After a few attempts at loading and reloading the cartridge, I discovered that the plunger was stuck at the bottom of the gun and wasn't going up inside the cartridge. So, all enthusiastic like, I took the grease gun apart to see why this was/wasn't happening. Unfortunately, I didn't realise I was unscrewing the handle and when the piston released from it, it was fired into the back of my container/shed, never to be seen again.

Anyway, I still had enough of the grease gun to try fitting the piston inside the cartridge and it doesn't bl**dy fit! The plunger is the same diameter as the cartridge outer, so it's never going to fit! Have I just got a cheap grease gun with the wrong size plunger inside it or am I doing something incredibly stupid here?

Any advice, rolling eyes, shaking heads, stroking of beards gratefully received,

Thanks :)
 
I bought this one the other week from Amazon relatively cheaply;
Hilka 84800120 Manual Grease Gun Set Pro Craft
 
Thanks both :)

I was tempted by a grease gun off a WWII tank that turned up on eBay recently, but everything I read said they're a bit of a pain to fill as you can't bleed them.

That one off amazon looks good enough for me - and it comes with a cartridge, so they must fit in the stupid thing!
 
Fit the plunger into the cartridge and push the cartridge down into the grease gun with the plastic cap on the top. The plunger will hold it down. Then take the cap off and screw the top on. Lastly push the plunger lever up.
 
Top tip: file a couple of flats on the tip of the nozzle once you get it sorted - it will then fit more easily into the tight space between the yokes of the propshaft. Personally I use the old school non-cartridge type gun.
 
lynall said:
Air locks in manual grease guns really pee me off!
Click to expand...
What pees me off most is grease not getting into the prop uj's and squirting all over the outside of the uj. Due to the awkward angles and needing 3 hands to hold the gun, operate the lever and keep the nozzle in line. While lying under the landy on the driveway. Messy. :mad:
 
Wimblowdriver said:
What pees me off most is grease not getting into the prop uj's and squirting all over the outside of the uj. Due to the awkward angles and needing 3 hands to hold the gun, operate the lever and keep the nozzle in line. While lying under the landy on the driveway. Messy. :mad:
Click to expand...

Decent grease gun ends help, I have found the best and smallest so far to be the ones from machine mart, I have taken the grinder to ones before to narrow the ends down so its easier to get them into the u/j yoke.
Also helps to have a hwwel of the floor to make rotating the prop easier, whatever you do it can be a pain.
Extended nipples help as well!
 
You must log in or register to reply here.

Similar threads

C
Copper Grease
Replies
16
Views
1K
Alibro
Alibro
Seph98
Turbo Hoses with oil
Replies
7
Views
722
miktdish
miktdish
S
Trouble attaching lid of heater matrix
Replies
3
Views
359
steve2286w
steve2286w
miktdish
Mess/seal/Core plug in transfer/transmission gear change housing
Replies
3
Views
480
miktdish
miktdish
styleruk
Bonnet sound proofing
2
Replies
26
Views
3K
Knappster
Knappster