R

rich201283

Member
I have stripped down a 2.25 5 bearing engine in the hope the bores were OK, I have measured the ring gaps and they are way out so it looks like a rebore is needed, the crank pulley has also got a score on where the oil seal runs, not sure whether I should rebuild the 5 bearing engine or the 3 bearing engine that's currently in it, are the 5mb much better? Also does anyone know the best place to get the rebore done around teeside?
 
I've took the pistons out and push the rings in the bore and measured the gap, the are out of tolerance, I haven't measured the bores as I don't have the tool.
 
rich201283 said:
I've took the pistons out and push the rings in the bore and measured the gap, the are out of tolerance, I haven't measured the bores as I don't have the tool.
Click to expand...
an old 2.25 is going to have worn bores unless its been rebuilt in recent years, not that that will stop it been used for many years quite often, it depends what your after
 
rich201283 said:
I'm rebuilding the whole vehicle so thinking I might as well go the whole hog a rebuild the engine
Click to expand...
in that case buy the appropiate pistons ie plus 20 unless it already is and get it bored to suit them, pistons vary in size so you buy 4 as a set and you get block bored and honed to leave correct clearance, you dont get it bored over size then buy pistons
 
If you're in the Manchester area phone LEC , they'll sort you out cheapest and best and really know their stuff and free postage next day if required
Lymm Engine Components
Unit 5 Birch Court
Grosvenor Grange
Warrington
Cheshire
WA1 4GD

Telephone:
01925 752458

E-Mail Address: sales@lymmengineparts.co.uk
 
I'm in teeside, yeah 160 for rebore then plus pistons and rings, was going to buy them myself but not sure how much rebore needs to be done
 
rich201283 said:
I'm in teeside, yeah 160 for rebore then plus pistons and rings, was going to buy them myself but not sure how much rebore needs to be done
Click to expand...
not bad for a rebore plus hone, the hone is the vital bit,piston and ring set likely 20 to 40 quid each
 
rich201283 said:
I'm in teeside, yeah 160 for rebore then plus pistons and rings, was going to buy them myself but not sure how much rebore needs to be done
Click to expand...
Phone LEC for advice and compare prices, you wont be disappointed and will save money:)
 
Just had the verdict from the engine reconditioner, He has advised it needs bored out to 030 but i need to supply the pistons because they are to expensive for them to get, The only ones i can seem to get are Britpart ones.
 
rich201283 said:
Just had the verdict from the engine reconditioner, He has advised it needs bored out to 030 but i need to supply the pistons because they are to expensive for them to get, The only ones i can seem to get are Britpart ones.
Click to expand...
id go for +40 ,id be surprised if +30 was still available
 
Surprisingly craddocks have them but can't advise what make the pistons are, and island 4x4 have the britpart ones in, the engine builder advised to get the 030 then the block is not on its limit
 
You must log in or register to reply here.

Similar threads

beerdude
3 or 5 Bearing engine?
Replies
1
Views
618
marjon
marjon
Castor
Series 3 Engine out top or bottom?
Replies
14
Views
1K
dag019
dag019
1
Broken Timing Belt
5 6 7
Replies
126
Views
6K
109Santana
1
P
Piston Ring Gap Positions - 1985 LR90 2.25 Petrol
Replies
3
Views
860
lynall
L
S
LAND ROVER DISCOVERY 3.0L 306DT I WANT TO FIT A GEN 1 ENGINE INTO A GEN 2
Replies
1
Views
277
lynall
L