matty_daak

Active Member

• Apr 27, 2012

• #1

After months of reading threads on here and toying with ideas I came to the conclusion that I was going to begin heavily modifying my disco! A few of the guys in my club have done bobtails but a few are not to my liking, ie look good but not very strong or very strong but look horrid.. I spent days and days trawling through Google images finding ideas for something I liked. I finally decided (in a moment of 'Ahh fu*k it!') that I was going to build a 2 door bobtailed pickup out of my 5 door disco! After sourcing the rear panels from a 3 door disco to save welding up the rear doors, I figured the first step was to begin the bob tail with the existing setup as it would need doing anyway. So why the pickup some may ask, well I wanted to keep a decent load area and build a rangie style drop tail gate, eventually I might look at a canvas back for it. But for now, 5 door bob

So here's a few piccies of the process...

First job was to strip all the back end out:

Good ole disco... rotted! To be expected I guess!

 

matty_daak

Active Member

• Apr 27, 2012

• #2

The first cut is daunting... I've measured out everything so the outer skin will overlap, the inner I'll cut shorter so it can be welded up nicely:

Once the outer skins were carefully removed the abuse with the big old 9" could begin! The result... half a disco!:

She's gonna be a little shorter when finished! The backend has lifted quite a lot after taking so much weight off it, I've worked out that it should drop down a bit once the boot door and spare go back on:

 

matty_daak

Active Member

• Apr 27, 2012

• #3

The factory rear body support will go back on with new fabricated mounts on the new rear cross member.

The scrap pile aint finished yet!:

It'll look something like this... excuse the line of the inner panel, I had to cut out a bit more rot, it will be levelled up and plated later :

 

matty_daak

Active Member

• Apr 27, 2012

• #4

Thats gonna improve the departure angle a bit

Just gotta 'trim' the chassis back next:

Something like that! Told you the scrap pile wasn't finished

 

sible88

New Member

• Apr 27, 2012

• #5

Looking good fella

 

matty_daak

Active Member

• Apr 27, 2012

• #6

So next to put a bit of strength back in that chassis! The new rear crossmember will be a lovely bit of 4"x4" box with a nice 4mm wall (sorry about the british measurements!) We've cut the chassis back on the corners of the legs so that the top and bottem could be tied into the new rear end. The box section was lifted to sit neatly under the original rear body supports and boot etc.

You can see how much the chassis needed fabricating to suit. The top of the original chassis welded on top of the new rear member gives extra strength when being tugged on

Next the sides were plated and welded all rounded, the edges are overlapped for a better weld:

Like this:

Gotta love the free plug...

 

Last edited: Apr 27, 2012

matty_daak

Active Member

• Apr 27, 2012

• #7

Thought we'd try out the arc from the arc... Yeah it just melted stuff! lol

Had a bit of a hole in the rear end so that had to be patched.. Before...

And after:

 

matty_daak

Active Member

• Apr 27, 2012

• #8

The rear body mounts had been plated before, one less job to do I guess!

A bit of a break from the rear crossmember to attack the rot, I figured lots of little bits would be easier than trying to fu*k about and get the right curve:

And the other side:

 

matty_daak

Active Member

• Apr 27, 2012

• #9

Lookin good!

And back to the cross member...

Got some extra strength in there by triangulation:

 

matty_daak

Active Member

• Apr 27, 2012

• #10

Check out this bad boy!

Nice bit of weld on that! You can try as hard as you like to rip that off... my money is on the rope breaking!!

 

matty_daak

Active Member

• Apr 27, 2012

• #11

Looks good with the stone chip on it

Next is matching up the body, tacking it in place and fabricating the new rear body mounts:

Damn thats smart if I do say so myself! What do you think?

 

matty_daak

Active Member

• Apr 27, 2012

• #12

Looking good fella

Click to expand...

Thanks sible88

 

Matt Baxter

Active Member

• Apr 27, 2012

• #13

Looks good so far mate, would love to do mine at some point how long has it taken so far?

 

matty_daak

Active Member

• Apr 28, 2012

• #14

Thanks for the feedback! So far it's taken an afternoon to strip it - tackling all the seized/rusted bolts sucked! Another afternoon to chop it up, followed by a trip to the A&E after an incident with the angle grinder... 3 hours of surgery to re-attach tendons and nerves, several stitches, a cast and a sling and some hardcore pain killers later... Another two afternoons welding the cross member and getting it to the stage it is now (with two mates helping for the last two afternoons as I can't work as well one handed!)

 

Freediscoranger

Active Member

• Apr 28, 2012

• #15

looks good! interesting read. am hoping to make my disco into a pickup when it finialy dies of rust!

 

GreenHornet

Well-Known Member

• Apr 28, 2012

• #16

That looks really good. Well done! Hope you get well soon.

Come on Matt - let's do yours, i will help and then we can do mine afterwards. Come on you know you want to. I will give you a full week of evenings so let's say 6 till 9pm for 5 days.

 

Dr_evil

Banned

• Apr 28, 2012

• #17

Looking good, keep updating

 

Matt Baxter

Active Member

• Apr 28, 2012

• #18

matty_daak said:

Thanks for the feedback! So far it's taken an afternoon to strip it - tackling all the seized/rusted bolts sucked! Another afternoon to chop it up, followed by a trip to the A&E after an incident with the angle grinder... 3 hours of surgery to re-attach tendons and nerves, several stitches, a cast and a sling and some hardcore pain killers later... Another two afternoons welding the cross member and getting it to the stage it is now (with two mates helping for the last two afternoons as I can't work as well one handed!)

Click to expand...

It was all sounding fine till the grinder incident, hope you are alright tho?

 

Matt Baxter

Active Member

• Apr 28, 2012

• #19

GreenHornet said:

That looks really good. Well done! Hope you get well soon.

Come on Matt - let's do yours, i will help and then we can do mine afterwards. Come on you know you want to. I will give you a full week of evenings so let's say 6 till 9pm for 5 days.

Click to expand...

thats not helping

 

Jinxy65

New Member

• Apr 29, 2012

• #20

Bloody good work mate. You and ya fellow club members have done well. Cant wait for the final pics.

Uv65