Windscreen washer question

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
owas

owas

Well-Known Member
Posts
1,213
I orderd a few bits to convert the windscreen washers on to the wiper arms, then realised I don't have just have a single nozzle but two separate ones on each side of the screen and they work fine.

Is it standard to have 2 seperate ones on the earlier 110s?
 
owas said:
I orderd a few bits to convert the windscreen washers on to the wiper arms, then realised I don't have just have a single nozzle but two separate ones on each side of the screen and they work fine.

Is it standard to have 2 seperate ones on the earlier 110s?
Click to expand...
Yes, standard on early OneTens. For a bit more water output you can put twin-jets where the single ones are, but if the current setup works fine than I’d be tempted to keep things original - depending on how original the rest of the Landy is being kept!
P.s you’ll know if they’re standard as you won’t have the centre hole stamped in the bulkhead where a twin-jet would go.
 
Yes it's a Good conversion is to replace singles with twin jets.

Only problem with jets on wipers they can suffer from cold to the exposed pipes.
 
I have my jets on the wiper arms. I have had them on there for around 2 years, actual use and not including this year while it’s been off the road.

I never had any problems with the cold, and freezing the washer fluid, but I normally run Halfords -20 or -30 fluid, neat, so don’t expect it to freeze up. I couldn’t get the -30 to freeze in the freezer, I set it to -28 I think. It’s good stuff.
 
The ones on my other car are on the wiper arm, and they're really good, that's why I thought I would do it but there's really no need, I'll leave it standard.

If any wants the clip on wiper blade nozzles when they arrive, let me know and I'll pop them in the post.
 
owas said:
The ones on my other car are on the wiper arm, and they're really good, that's why I thought I would do it but there's really no need, I'll leave it standard.

If any wants the clip on wiper blade nozzles when they arrive, let me know and I'll pop them in the post.
Click to expand...

Which type of clip on nozzle are they?
 
I too have nozzles on the wipers, I find they work much better than the originals. I replaced the plastic tubing supplied with silicon tubes. Never had a problem with freezing. But as above use a high percentage of anti freeze and the new piping takes a few turns round heater pipes.
 

Attachments

  • IMG_20181226_111435.jpg
    IMG_20181226_111435.jpg
    61.2 KB · Views: 131
owas said:
This one
Click to expand...

I was going to ask if I could give them a try instead of the ones I have fitted, but I’m not sure them ones would be any better. I’m not trying to slag them off, it’s just mine have 3 nozzles on them, all in the same direction. I keep looking for ones with only 2 towards the wiper blade.

The pump doesn’t appear to generate a lot of pressure with mine, as it’s effectively 6 nozzles instead of the standard 2.
 
That's all I done. Mine looks rough but works.(take photo in the morning)
This kit you have to cut a pipe & replace it.

I'm trying to find a screeen wash bottle that has a coiled pipe which is heated by the water. Think it's merc or iveco
 
Hicap phill said:
That's all I done. Mine looks rough but works.(take photo in the morning)
This kit you have to cut a pipe & replace it.

I'm trying to find a screeen wash bottle that has a coiled pipe which is heated by the water. Think it's merc or iveco
Click to expand...

The cutting of the pipes is what put me off that kit. It’s an extra place for leaks to occur, so if doing what you have done is working, then I may try that when I get started.
 
Hicap phill said:
The merc link uses the rad water to heart it. Still looking for an electric version.
Electric would be better as quicker than letting a landy warm up.
Click to expand...

I did think about using water, but like you say it will take its time to warm up, and I wonder how the sealing of it all will work.
 
You must log in or register to reply here.

Similar threads

Musher3
Upside down wipers!
Replies
11
Views
547
Musher3
Musher3
S
Windscreen Wiper switch question
Replies
4
Views
596
TS2304
TS2304
M
L322 Westminster 2012 windscreen wiper fault
Replies
0
Views
381
mybestcarever
M
Keith_L
Disco 2 Are the windscreen washer jets adjustable?
Replies
7
Views
1K
backinblack
backinblack
Officerdibble
Rear washer issue
Replies
2
Views
653
Officerdibble
Officerdibble
Back
Top