Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
Thanks. Never been called upon to do that.
Will Wolfs Fit?
- Thread starter steveyorks
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Thanks. Never been called upon to do that.
steveyorks
Well-Known Member
- Posts
- 827
- Location
- west yorks
Ok so they fit that's good. I used to have a Disco 2 so hence my confusion about PCD. Thank you one and all for the replies its much appreciated.
Discokids
Well-Known Member
- Posts
- 3,160
- Location
- Derbyshire
Ill try what I like on a public forum thank you very much, unless you've got the authority to tell me otherwise?
If it's not a problem, why do they sell longer studs?
They may well do so, but the fact is it never has and will never happen, you could say the same for anything you fit, fix or modify your self, all these modified vehicles driving around that were modified my an untrained, inexperienced person on their driveway whose only knowledge of what they are doing is what they have read on forums like this one, who may or may not fully understand what they are doing in the first place and the consequences they face when what they are doing goes horribly wrong, I have seen advice being dished out on these forums for years that is pretty much nonsense based on little or no facts and is basically the opinion of someone who is untrained, inexperienced and sometimes just plain stupid.
Don't get me wrong , there arse some very knowledgeable people on here, James springs to mind (bit of arse licking there James) but there are also some folk who really shouldn't be allowed anywhere near a tool box never mind the working of a motor vehicle.
Well , that went off on a bit of a tangent, so , back to the original question , Wolf wheels are perfectly safe and legal on small studs so long as you tighten them up properly, if you cant do that get a garage to do it for you.
Why don't you phone them up and ask them? Wouldn't hurt.
Discokids
Well-Known Member
- Posts
- 3,160
- Location
- Derbyshire
Because I don't actually care, that's why.
It's a personal preference I suppose, I just wanted the op to be aware that when he fits them he might get a surprise looking at the nuts. Me, I'll be buying and fitting the longer studs.
Just found these int garage - a third option
I saw a Heritage 90 the other day, Wolf wheels and short studs, if Land Rover were selling them with short studs they must be happy with them.
Do a Google etc search for Heritage 90 and look at the wheels, all the one's I have seen so far have short studs.
Not trying to be smart, just an observation.
Do a Google etc search for Heritage 90 and look at the wheels, all the one's I have seen so far have short studs.
Not trying to be smart, just an observation.
Jam1
Well-Known Member
- Posts
- 1,315
- Location
- Staffordshire
How tight do you need to do them up to get one and a half threads sticking out the end?Because I don't actually care, that's why.
It's a personal preference I suppose, I just wanted the op to be aware that when he fits them he might get a surprise looking at the nuts. Me, I'll be buying and fitting the longer studs.
Just found these int garage - a third optionView attachment 141253View attachment 141254
Discokids
Well-Known Member
- Posts
- 3,160
- Location
- Derbyshire
Don't think there's a scaffold tube long enoughHow tight do you need to do them up to get one and a half threads sticking out the end?
How tight do you need to do them up to get one and a half threads sticking out the end?
Tight enough to widen out the holes on the actual wheels with the wheel nuts, you know when you over tighten and you hear a crack? Tighter than that.
callisr
Well-Known Member
- Posts
- 615
- Location
- Burton-on-Trent, Staffs
I do mine to 170nm. I use a torque wrench cuz it’s as easy to get to as the breaker bar is. It’s surprising how untight the nuts feel compared to how tight I would murder them up with a breaker bar!
I have a link somewhere to the mod bulletin thing. I’ll see if I can find it....
Rich
I have a link somewhere to the mod bulletin thing. I’ll see if I can find it....
Rich
callisr
Well-Known Member
- Posts
- 615
- Location
- Burton-on-Trent, Staffs
Seems the link I have is dead. The recommended torque is still 170nm though (or til it creaks!)
Rich
Rich
That's the thing , when you murder them up you run the risk of damaging the wheels, nuts or studs, no need to have them way too tight.
flat
Well-Known Member
- Posts
- 9,075
- Location
- Far away from you!!
Discokids
Well-Known Member
- Posts
- 3,160
- Location
- Derbyshire
I try my best
flat
Well-Known Member
- Posts
- 9,075
- Location
- Far away from you!!
rob1miles
Well-Known Member
- Posts
- 3,565
- Location
- Slough and Bath
I like the argument that since LR sell the longer studs it would be prudent to fit them, but its completely undermined by the photos of LR Heritage vehicles with short studs. I think the most usefull thing would be a polite letter to LF Heritage asking for a copy of the Certificate of Conformity for the wheels and studs and see what comes back. Either nothing (most likely) or a cert saying its ok, or they change them? I wonder?
frog hopper
Well-Known Member
- Posts
- 4,764
- Location
- france
I had exactly the same question when I wanted to fit wolf wheels to my 1985 110 (V8 Csw), so I asked my mate. This chap worked for 30 odd years in a research environment as a precision engineer +, the + bit being that he would design and make stuff to enable precision engineers to make stuff, if you see what I mean.
Anyway he was meant to be rather good at it, so I asked his opinion.
Reply as far as I remember was that ordinary original manufacturer stuff was in reality rather rough and ready, no matter how well they claimed to be making whatever.
As far as fitting wheel nuts, as long as all mating faces were clean of bulky contaminents (grains of sand/mud/rust whatever) then nuts that held the same or greater length of thread as the max dia of the thread on the stud would be well within safety limits. Maybe give them 10% more torque than normal,but no more than that.
Basically, just get on with it. That advice was for me to follow if I chose to do so. If you want to do the same then so be it.
As for the comments above about the military not bothering to change studs when fitting wolf wheels, I can't believe they didn't at least phone LR during a quiet moment and ask if it would work out.
Anyway he was meant to be rather good at it, so I asked his opinion.
Reply as far as I remember was that ordinary original manufacturer stuff was in reality rather rough and ready, no matter how well they claimed to be making whatever.
As far as fitting wheel nuts, as long as all mating faces were clean of bulky contaminents (grains of sand/mud/rust whatever) then nuts that held the same or greater length of thread as the max dia of the thread on the stud would be well within safety limits. Maybe give them 10% more torque than normal,but no more than that.
Basically, just get on with it. That advice was for me to follow if I chose to do so. If you want to do the same then so be it.
As for the comments above about the military not bothering to change studs when fitting wolf wheels, I can't believe they didn't at least phone LR during a quiet moment and ask if it would work out.
Rougharse Racing
Well-Known Member
- Posts
- 883
- Location
- The Grim North
I imagine that someone at the MOD picked up the phone and had a chat with Land Rover about stud length before ordering thousands of Wolf wheels to retro-fit to their fleet.
Perhaps the longer studs are more of an issue for 130's, particularly those plated at over 31/2 tonnes such as ambulances.
Perhaps the longer studs are more of an issue for 130's, particularly those plated at over 31/2 tonnes such as ambulances.
