danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
I never seem to find them at that price or even close enough to even go and have a look at them.
Why have you chosen a defender?
- Thread starter Marmaduke
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Bugger it failed
I was hoping it would be catastrophic but I've fixed the lights, off to craddocks tomorrow for a timing kit and front hub bearings. Then to buy a lower end engine for a replacement sump.I'm off work for 11 days so I'll swap the insurance over and run it for a week to decide but discos are a way nicer place to be than tratters.
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
I'm planning on taking it to Wales for a play on Saturday
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
Fuses & Bulb bi chance ??
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Just a bad earth, I gave it a slap and it came back on
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
I'm planning on taking it to Wales for a play on Saturday
Don't F/in break it yu only just got it !! 
Well in theory its a 1995 3000GT Twin Turbo with 86k miles, but I bought it with the engine in bits after a massive overheat and am slowly putting it back together with my limited mechanical knowledge!
And yes, it is rare that it is 100% standard, minus the painted wheels
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
It's pretty low. I'm actually really enjoying not having to stand on a box to work on the engine... though that may be because it's in the garage!
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
I do you a good deal on it
D.I.S.C.OThat'd do, bit rougher than mine though
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
Have you found out why c/l int workin yet ??
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
How good a deal lol.I do you a good deal on it
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Fuse had gone and the nsr door motor needs looking at, thanks for the heads up though
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
You can check motor with 12 volts (door card off) If that dunt work brushes in motor crackerd New motor of the bay about £ 1.50 ish ! but you have to put your gear wheel on !
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Probably not cheap enough for you
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
@Marmaduke Eltop Electonics £1.32 MR01 motor
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Cheers for that. If I put the fuse back in the motor will pop the button up and down but it sounds like the motor keeps going for another few seconds so it might just need adjustment. I wouldn't mind but when I last broke a discovery I weighed all the doors and internal gubbins in
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
You should NEVER do that !!!!!If it's working then yes prob needs adjusting
Co-Pang-Yang
Well-Known Member
- Posts
- 2,930
- Location
- Colchester, Essex
Got a door lock that don't work on mine.
Still don't understand how you fix them
Still don't understand how you fix them
Similar threads
