What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
mikescuba
Well-Known Member
- Posts
- 2,731
- Location
- France, Loire, Rhone Alpes
You mean, like this? This was the old hood I have just removed
Now that's how a Defender should look. Nice shot.
- Posts
- 1,855
- Location
- Selby, North Yorkshire
Sorry to be the odd one out but I would prefer the khaki/brown coloured one as a bit of contrast to the black.
ok, I'm off now.
ok, I'm off now.
- Posts
- 6,395
- Location
- North Perthshire
..... changed rear brake pads, and replaced fuel filter and holder. Still need to drill out the holes for the offside mudflap setup.
cornish rattler
Well-Known Member
- Posts
- 6,432
- Location
- Manc chester
Not on landy but spent a couple of hours sorting my new bench out wasn't realy happy with how the bench drill and vice was positioned so swapped them round then tomorrow i will move my roll cab to the opposite side of the bench as its too much in view when the garage door's are opened, can't be seen if it was at the other end of the bench in the corner 
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
Welded a bit.
cowasaki
Well-Known Member
- Posts
- 1,517
- Location
- North West England
Fabricated a small bracket for the dash, changed an exhaust rubber and scrubbed the transfer box, gearbox and around the diff pinion seal around with engine cleaner and a jet wash......
doriz
Well-Known Member
- Posts
- 17,312
Great day for it, I was stuck in work
mikescuba
Well-Known Member
- Posts
- 2,731
- Location
- France, Loire, Rhone Alpes
If its from Paddocks I went through three of them in a very short period of time.
- Posts
- 83,282
- Location
- Embasinga stocæ
started to make a tablet bracket for the disco. pics tomoz after painting.
doriz
Well-Known Member
- Posts
- 17,312
Ordered a new alternator
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
made more holes in it
- Posts
- 83,282
- Location
- Embasinga stocæ
Yep it was. They're sending out another.
It wasn't a ****part either. If it happens again il have to source one elsewhere.
Nice.
Why not go for a windscreen mount? You wouldn't have had holes in the dash
Drove it - Towed my friends car down the road after he wrote it off poor chap. And stuck a new number plate on me new flatbed trailer ready for work towing staging next week! Picked up two 20l jerrys from work, ready to add to the two 100l bowsers for all the red I need to move around. Big job next week - hopefully the old girl can put up with it all.
poor chap. And stuck a new number plate on me new flatbed trailer ready for work towing staging next week! Picked up two 20l jerrys from work, ready to add to the two 100l bowsers for all the red I need to move around. Big job next week - hopefully the old girl can put up with it all.
landrover11019
Active Member
- Posts
- 852
- Location
- essex
Changed the rear radius arm bushes.
Had to chisel the rubber doughnuts out to get to the nuts and bolts.
On one side someone had welded the bolt to the axle bracket!!!
Took 6 bloody hours in total.
Had to chisel the rubber doughnuts out to get to the nuts and bolts.
On one side someone had welded the bolt to the axle bracket!!!
Took 6 bloody hours in total.
