What have you done to your Landie today.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
discomikey said:
holy frick chris haha, good job youre safe. and there was me thinking youd lost a lining from a pad haha.

im assuming that youve torqued them up all to F tight
Click to expand...

All bolts are now F T yeah um very lucky to be alive still. Had loads of play in swivels tightened them right up again so jobs a Gooding with that.

No 1.40 wasnt bad but the 15 quid in fuel to get to the stealers in my dads range rover wqs annoying.
 
mikescuba said:
HI Discomiky, Just as a matter of interest how long does it take to remove a bulkhead?
Mine is fine but I have heard that this is a weakness on them. I still have to fit my footwells which I have put off due to the cold weather.
Click to expand...

depends on the model, how much your stripping and what the state of the wiring is.

i completely stripped Brian and it was one of the last things to come off.

whats needed is the wings need to come off (30 mins max)
floor panels and tunnel come out (again 30 mins max)
disconnect the steering (10 mins max) easy enough to do
support it with some sort of crane/lift (5 mins)
undo the support brackets, i undid from chassis as it seemed easier (5 mins)
unbolt windscreen and prop out way (30 mins max depending on how you do it)
disconnect wiring
undo the main outrigger bolts (5 mins max)
brake lines + clutch (5 mins)

lift free very carefully

i may have missed something, its not too hard but can seem a bit daunting i would put aside half a day from a fully built landy cos bolts can be siezed etc. i stripped Brian down to a bare rolling chassis in 13 hours but i was on a mission and nothing was siezed cos i had rebuilt him not too long ago.
 
Freediscoranger,

No 1.40 wasnt bad but the 15 quid in fuel to get to the stealers in my dads range rover wqs annoying.
Click to expand...

Is it a decent stealers? and where is it?

Packed the landy for the trip up North.
 
bought a set of wheel bearings on my way home..

checked the rear bearings and they just wanted adjusting...

1st time i've fixed summat that didnt cost me muny..

well i suppose it did cos i now got a set of bearings i aint used....
 
bluehaze said:
Freediscoranger,



Is it a decent stealers? and where is it?

Packed the landy for the trip up North.
Click to expand...

Tim fry land rovers in Cheltenham. Theyre my recommendation, they prices are reasonable for the expertise. got a second hand breakers and a new parts show room, you name it and theyll have it in by the next day at the latest. Tim fry is a family friend as well so that helps :D or for general parts go to TH White in Wooten Bassett .
 
Last edited:
Freediscoranger said:
Tim fry land rovers in Cheltenham. Theyre my recommendation, they prices are reasonable for the expertise. got a second hand breakers and a new parts show room, you name it and theyll have it in by the next day at the latest. Tim fry is a family friend as well so that helps :D or for general parts go to TH White in Wooten Bassett .
Click to expand...

:5biagree: Frys' is pretty good
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
469
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
565
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
826
Knappster
Knappster
I
Re-coding of ABS Module after repacement
Replies
10
Views
906
invisible999
I
C
Freelander 1 crank no start
Replies
1
Views
1K
niccage
N
Back
Top