timtheenchanteruk
Well-Known Member
- Posts
- 4,633
- Location
- Leeds
bought some hammerite to do the rear X-member with one evening this week
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
andrewblueboy
Active Member
- Posts
- 245
- Location
- bolton
been fitting box section on passenger side with new mounts.not fully welded as ran out of wire,but at least its in place
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Made some rocksliders
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
:nopics:
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
bloody expensive ent it!
Hitchhiker
New Member
- Posts
- 29
- Location
- Barnsley/Sheffield
That’s the excitement of the carousel ride called Land Rover!wont be long before it's a nightmare then.
foxyjam
Active Member
- Posts
- 119
- Location
- Bourne, lincs
Took the timing cover off ready to fit the new cloyes duplex timing set tomorrow afternoon.
Going to give the front cover a bit of a clean whilst I'm at it.
Think the old chain is a bit past it, fair bit of slack in it. Will compare with new FireWire when I've got it off.
Going to give the front cover a bit of a clean whilst I'm at it.
Think the old chain is a bit past it, fair bit of slack in it. Will compare with new FireWire when I've got it off.
Attachments
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
bigvinnie
Active Member
- Posts
- 748
- Location
- Catterick North Yorkshire
sourced a new turbo!
fit this along wea the decat on sunday whilst on duty.
hopefully cures ma bloody "air noise"
fit this along wea the decat on sunday whilst on duty.
hopefully cures ma bloody "air noise"
Hitchhiker
New Member
- Posts
- 29
- Location
- Barnsley/Sheffield
I have painted my sliders and done some prep ready to fit as soon as the chance arises.
Hitchhiker
New Member
- Posts
- 29
- Location
- Barnsley/Sheffield
mines more like a round-about of errors
What's wrong with it, I thought it was all working well?
it is
but they expect tales of woe from the freelanders, especially the k series.
when are the sliders going on?
i may assist if you do it after tea one night this week
jimbell
Member
- Posts
- 76
- Location
- wolverhampton, west mids
been busy the last few days rebuilding a 300tdi lump well, freshening it up a bit should i say.
today has been new headgasket, timing belt and tensioners aswell as fixing the engine stand and changing the front crank seal. tommorow will be new stat, w/pump, rear crank seal and the start of stripping down the landy ready to take its new heart.... and probably fitting some new brake pads for the wifes landy.
today has been new headgasket, timing belt and tensioners aswell as fixing the engine stand and changing the front crank seal. tommorow will be new stat, w/pump, rear crank seal and the start of stripping down the landy ready to take its new heart.... and probably fitting some new brake pads for the wifes landy.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Sliders 80x80x5mm box with 2" nominal tube in medium gauge
Weldings a little scruffy on the threaded top hats but as its going on my own vehicle I'm not arsed
Weldings a little scruffy on the threaded top hats but as its going on my own vehicle I'm not arsed
Last edited:
Mainlander
Active Member
- Posts
- 234
- Location
- Kettering
Bought a friend for my disco 2, a lada niva for pay and play days .
Wonder if a 200tdi lump will fit in it?????
.Wonder if a 200tdi lump will fit in it?????
Bought a friend for my disco 2, a lada niva for pay and play days
Wonder if a 200tdi lump will fit in it?????
fiat twin cam
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
Mainlander
Active Member
- Posts
- 234
- Location
- Kettering
Hmmm, choices???
