gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
ok,not far from me.tyldesley.
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
ok,not far from me.tyldesley.
Wiganerdan
New Member
- Posts
- 149
- Location
- Wigan
Well if you see a big turquoise box rambling around give me a wave.
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
Dr No
Active Member
- Posts
- 205
- Location
- Brecon Beacons
threatened to beat it with large stick basil faulty style
If you do Baggy can you get someone to film it so we can have a giggle?
Dr No
Active Member
- Posts
- 205
- Location
- Brecon Beacons
Swivel pins and bearings took me a day on my Fender which included fitting new wheel bearings ... not a bad job but quite greasy
Sounds encouraging. The bit about using the right shims to get the tension right worries me a little, but I might give it a go.
)
timtheenchanteruk
Well-Known Member
- Posts
- 4,633
- Location
- Leeds
got me a bigger hammer to aid with persuasion.
Andy Land
Well-Known Member
- Posts
- 4,499
- Location
- ... en route to Cuckoosville.
Sounds encouraging. The bit about using the right shims to get the tension right worries me a little, but I might give it a go.
With new swivel pins and railko bushes you are best to put all the shims on to start with and then check the pre-load using a cheap set of fishing scales. Pre-load should be around 8 - 10lbs. If it is too loose simply remove a few shims until you get the load right. It's all explained on here if you get stuck
Fitted a kill switch after some dodgy bloke in a transit pick up turned up asking if I want to sell it. Now when its turned off the engine just turns over without firing, sounds like it has no fuel.
Gonna invest in some other bit when Ive got some cash too.
Gonna invest in some other bit when Ive got some cash too.
mikescuba
Well-Known Member
- Posts
- 2,731
- Location
- France, Loire, Rhone Alpes
I'm getting worried, mine has been running like a dream for the last few months. Something must be building up.
Andy Land
Well-Known Member
- Posts
- 4,499
- Location
- ... en route to Cuckoosville.
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
Im planning on doing exaclty the same! dont wan sum fukker trying to drive it off!
There is a central locking kit with alarm for 2 doors on flea bay for £30 and a gps tracking thing for just under 60 on amazon. They are next on the list for me. Then I might look at a fuel starving valve. fooking pikeys thinking they can nick me stoof!
DEFENDER90-DAZ
New Member
- Posts
- 3,239
- Location
- Scotland - Houston
Oil and filter change - now the oil pressure gauge reads 35psi on idle
Fitted new windscreen wipers
Fitted a bracket for the tow bar electric plug
Fitted my waterproof winch cover
Adjusted the washer jets
Daz
Fitted new windscreen wipers
Fitted a bracket for the tow bar electric plug
Fitted my waterproof winch cover
Adjusted the washer jets
Daz
DEFENDER90-DAZ
New Member
- Posts
- 3,239
- Location
- Scotland - Houston
Cheers Daz, any suggestion on the best place to fit it? Arn't most of the fuel pipes steel?
DEFENDER90-DAZ
New Member
- Posts
- 3,239
- Location
- Scotland - Houston
Somewhere between the tuel tank and the fuel lift pump
Daz
Daz
- Posts
- 6,392
- Location
- North Perthshire
Bought a Disco....
Somewhere between the tuel tank and the fuel lift pump
Daz
Cheers mate, I shall have a looky see
JoelC
Active Member
- Posts
- 776
- Location
- South Yorkshire
Covered it over with a big tarp - to avoid any more water entry...
J
J
