What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Dr No
Active Member
- Posts
- 205
- Location
- Brecon Beacons
Off to get stainless sheet for switch housing, and a trolley jack. and turrets for front shock mounts. Gonna fit turrets, springs, shocks, dis cones, spring holders, new springs on the back, spring holders and dislocation cones. Then the Safari Snorkel, and drag a new mini loom in place for switch gear.
Gonna be busy.........
Gonna be busy.........
gallaghb
Active Member
- Posts
- 179
- Location
- Woodford Green, Essex
Took roof box off for tomorrows pay and play. Just about to check oil levels etc for tomorrow. Then might have to give some money to the government for fuel... So nothing major.
nathan5346
Well-Known Member
- Posts
- 11,939
- Location
- oldbury
Had the 3 amigo lights reset...Thanks to Lanny
DEFENDER90-DAZ
New Member
- Posts
- 3,239
- Location
- Scotland - Houston
Fitted my 'fabricated' heated washer system 
Fitted new battery
Daz
Fitted new battery
Daz
uncle albert
New Member
- Posts
- 1,111
- Location
- near louth n/lincs
how about a picy thenFitted my 'fabricated' heated washer system
Fitted new battery
Daz
DEFENDER90-DAZ
New Member
- Posts
- 3,239
- Location
- Scotland - Houston
Nah have to get the patent sorted first
Daz
Daz
uncle albert
New Member
- Posts
- 1,111
- Location
- near louth n/lincs
spoil sport
DEFENDER90-DAZ
New Member
- Posts
- 3,239
- Location
- Scotland - Houston
spoil sport
OK....................Have a look here: http://www.landyzone.co.uk/lz/f8/windscreen-washer-heater-anyone-tried-201281-4.html#post2179067
Daz
uncle albert
New Member
- Posts
- 1,111
- Location
- near louth n/lincs
got it . sounds good might well give it a go thanks
DEFENDER90-DAZ
New Member
- Posts
- 3,239
- Location
- Scotland - Houston
have another look mate - just added a pic Daz
uncle albert
New Member
- Posts
- 1,111
- Location
- near louth n/lincs
just seen it on other thread ta
ratty
I'm not special I'm limited edition
- Posts
- 34,277
I took mine for a spin to get some coal. I have run the fuel tank down to empty ready for re-seating the fuel tank seal one day this week.
martin1512
Well-Known Member
- Posts
- 3,941
- Location
- Half way up a cliff in Dorset
Changed clutch slave cylinder. Should have taken 1 hour, ended up taking 3 thanks to rounded bolt heads
ratty
I'm not special I'm limited edition
- Posts
- 34,277
Changed clutch slave cylinder. Should have taken 1 hour, ended up taking 3 thanks to rounded bolt heads
Get yerself some rounded nut removers.:doh:
JNEC
Active Member
- Posts
- 416
Changed the warn out uj on the rear prop for a nice new gkn shiney one!!
Fatboy11
New Member
- Posts
- 1,074
- Location
- Thatcham, Berkshire.
+1 couldn't do without mine now !
martin1512
Well-Known Member
- Posts
- 3,941
- Location
- Half way up a cliff in Dorset
I've got some, it was the nut that holds the fluid pipe into the cylinder, so nut extractors wouldn't go on. It had seized solid, and not even mole grips could get enough of a grip. I ended up taking it off with the pipe still stuck in the cylinder, and replaced cylinder & pipe.
DEFENDER90-DAZ
New Member
- Posts
- 3,239
- Location
- Scotland - Houston
Just fitted my heavy duty winch isolation switch
Daz
Daz
