What have you done to your Landie today.

DEFENDER90-DAZ · Sep 11, 2012

Freed off the diff lock linkage - at last!
Took a pic of my disco:

timtheenchanteruk · Sep 11, 2012

put a litter tray under it in the car park at work till I fix the leak!!

mikescuba · Sep 11, 2012

Sorted out why the brakes were pulling to one side. Rear brakes just needed adjustment. On the front the axle oil seal had gone and oil was dripping onto the disc.

mikescuba · Sep 11, 2012

The paint has gone down to bare metal on a couple of places on the doors and the rear door the paint has blistered in several places along the bottom. Do you need to put a primer on before painting where the paint has gone down to bare metal. I am thinking of trying out a hand painting job. I do have a compressor with all the spray toys but never used it. I thought I might do a couple of panels at a time unless anyone on here can advise me different.

chunkymunky · Sep 11, 2012

mikescuba said:
The paint has gone down to bare metal on a couple of places on the doors and the rear door the paint has blistered in several places along the bottom. Do you need to put a primer on before painting where the paint has gone down to bare metal. I am thinking of trying out a hand painting job. I do have a compressor with all the spray toys but never used it. I thought I might do a couple of panels at a time unless anyone on here can advise me different.

I have used a wire brush attachment to remove all bubbling

ImageUploadedByTapatalk1347372360.685722.jpg

then I will use a sand disk attachment to fine sand it. Then etch primer it as aluminium is poor for grip qualities, then sand lightly. Then a well shaken spray can from my old halfords man using trade card. Then clear lacquer. Hopefully a good finish as getting ready for selling now 😒

mikescuba · Sep 11, 2012

Thanks chunkymunky. I will have to find out what the French equivalents are for etch primers. I think I need to give mine a total paint job though.

chunkymunky · Sep 11, 2012

mikescuba said:
Thanks chunkymunky. I will have to find out what the French equivalents are for etch primers. I think I need to give mine a total paint job though.

primaire d'accrochage i think you will find

stops the paint flaking.

i have......and still am........

removing all bubbling from outside, removing all the goddam double sided sticky tape from inside the rear and sanding down.

filling and treating any areas i am not happy with.

replaced all the lenses for side lights etc.

put liner in the rear, just looking for cheap arch covers if anyone has any for a 90 going will pay or swop.

trying to find a local fabricator to make me 4 brackets to complete the fitting of fold down rear seats.

90ben · Sep 11, 2012

i cut my old nearside footwell out completely on the 90 and welded a new one in. then just for good measure i welded some nice new plates into a friends chassis so he could get an MOT

good times

gsxbuzz · Sep 11, 2012

Just finished fitting 2" sping spacers and new shocks

easye1 · Sep 12, 2012

sprayed waxoil in my box sections, and in the rear holes in chassis and rear crossmember,
then my old compressor packed up.
still got to buy 4 grommets @ 1.4 mm dia to plug the holes I drilled into the sides of box section under doors where I ran the waxoil lance through.

ratty · Sep 12, 2012

Temporarily fitted a volt meter to the mud console and modified the charger lead for my phone cos it wouldn't fit due to the case I have fitted.

a2dds · Sep 12, 2012

Tried to tune up my 200tdi today... did the injector pump stuff... still need to do a bit more, started raining and I had to go give blood. Pfftt!

Also tried to turn the "smoke screw" or what I thought was the smoke screw... it was not gonna budge :/

Not sure if there is much of a power increase or not... still got some tinkering to do thought I guess

OxonLandy · Sep 13, 2012

a2dds said:
Also tried to turn the "smoke screw" or what I thought was the smoke screw... it was not gonna budge :/

the smoke screw

like the one James Bond has when he wants to get away from the baddies?

LandyRover23 · Sep 13, 2012

^^^^^ like

burrito · Sep 13, 2012

Removed the EGR valve.

Series71 · Sep 13, 2012

removed the nearly new battery and put it in the golf

baggyjim · Sep 13, 2012

Series71 said:
removed the nearly new battery and put it in the golf buggy

( edited for accuracy )

lcbandit · Sep 14, 2012

Took off road tyres out of the back n sold em, uj turned up so prop getting done on sat hopefully

Bix · Sep 14, 2012

Gave her a big time service. Diff oil can't have been done for some time as it was like tar, had to flush the diff a few times to clean it all out. Rear calliper pistons were seizing, so freed them off. Replaced coolant too (plus wash the sludge out of the rad) as it was so diluted was only rated for about -7c, which isn't good enough for these parts, when over the last two winters it has dropped to around -25c.

I hope the many pounds of oils, fluids and filters will improve some of the sluggish when cold issues.

a2dds · Sep 14, 2012

OxonLandy said:
the smoke screw like the one James Bond has when he wants to get away from the baddies?

Yea... thats the one... so I can leave the bad boy racers behind in their clios the moment the lights turns amber!

I think its supposed to be the low end fuel screw or something, the one that is on the outside of the pump. Cant see the tack weld on it so cant get it free

What have you done to your Landie today.

New Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

New Member

Well-Known Member

New Member

New Member

Member

Attachments

Banned

I'm not special I'm limited edition

Active Member

Active Member

New Member

Active Member

Space man

New Member

Well-Known Member

Loading...

Active Member

Similar threads