What have you done to your Landie today.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Should do that fairly easily i would think. i'm just waiting for some sun now so I can see what it's capable of! i've bought on the premise that it'll keep my coolbox ticking over - that's a 35W input at 3A and the panel is rated at 40, so hopefully i'll be on to a winner.:cool2:
 
Fitted new PAS pump as old one died day before MOT.

Then i failed MOT on lack of offside reflector and inefficiant handbrake. so knicked reflector off old bicycle in the garage and adjusted handbrake.

All passed.

Not bad for a 22 yr old 110
 
pepperedwelly said:
Should do that fairly easily i would think. i'm just waiting for some sun now so I can see what it's capable of! i've bought on the premise that it'll keep my coolbox ticking over - that's a 35W input at 3A and the panel is rated at 40, so hopefully i'll be on to a winner.:cool2:
Click to expand...

rated at 40w with good light... remember this is England!
 
Fitted a nice new rad after my other gave up on me.
 

Attachments

  • uploadfromtaptalk1341521549458.jpg
    uploadfromtaptalk1341521549458.jpg
    70.8 KB · Views: 177
Replaced a small bit of brake pipe which was an advisory on last years MOT as this years MOT is due soon:rolleyes: and then spent fookin hours releasing and replacing two of the three bleed nipples on a caliper to bleed the system:mad::mad::mad:
Surprising how efficient the brakes are now with fresh fluid in.:)
 
Won a pair of spots on ebay for 99p, dug out a lightbar someone gave me a few years ago and added 'em to the Disco .. Not wired up yet, waiting for a couple more auctions to end .. ;)

003.jpg

002.jpg


Had to make a couple of brackets for 'em out of square section tube, to make them fit below the bar, but all seems solid .. ;)
 
Paul D said:
Won a pair of spots on ebay for 99p, dug out a lightbar someone gave me a few years ago and added 'em to the Disco .. Not wired up yet, waiting for a couple more auctions to end .. ;)

003.jpg

002.jpg


Had to make a couple of brackets for 'em out of square section tube, to make them fit below the bar, but all seems solid .. ;)
Click to expand...

You call that a light bar :p lol ? This is a light barImageUploadedByTapatalk1341525595.309557.jpg
 
will put a pic up tomorow of my button, if i may say so, well proud of it, changed one of the old volume buttons for a spare rear windscreen wiper button, and used a relay, i used power to the light in the switch to close relay, so i can leave the roof lights on with out atleast the sidelight being on which = beep when you open door= me less likely getting a flat battery lol
 
No, gonna run the wire through the bar then down the front of the offside windscreen trim, then into the engine bay and through bulkhead to a switch/relay wherever there's room etc.

Sounds like yours is doing what I want too, I'll need the lights working irrespective of legality for a couple of weeks, but then I'll wire 'em properly to high beam .. ;)
 
yh, they need to be on a separate switch to the high beam for the mot, and dont wire them straight off high beam or you may melt your light stalk haha, if you want any pics for help just message me and i will put some up :)
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
536
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
631
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
911
Knappster
Knappster
Mooky
Replacing thermostat
Replies
14
Views
560
Mooky
Mooky
I
Re-coding of ABS Module after repacement
Replies
10
Views
988
invisible999
I
Back
Top