gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
never mind the landy,did you get the feckin job??
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
never mind the landy,did you get the feckin job??
will find out next week
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
will find out next week
ok,you will have to get the local coven of witches to cast a spell for you.
easye1
Banned
- Posts
- 8,557
indeed you may have done.
I infact have had ep140 in both hubs for a few months,
but the summer heat made it drip out,
but its still dripping so it must still be there,
so I`m going the one shot route to cure it..
the ep140 made one clicking cv joint so much quieter,
so the grease hopefully will be even better,
if i get it the matiz and 109 are goingok,you will have to get the local coven of witches to cast a spell for you.
Clanforbes
New Member
- Posts
- 1,503
- Location
- Perthshire
Probably yes, as I undestand it these things will just about adapt anything to any car .com ?
- Posts
- 356
- Location
- Aberystwyth Mid Wales
Bought it a safari snorkel. Looking forward to it turning up as it'll give me something to do next week.. God I hate school holidays....
Richie Box
New Member
- Posts
- 97
- Location
- Wrexham
Tried fitting rock sliders last night, drivers side- no problem, passenger side- tried knocking in to outrigger to find half my chassis falling on the floor!
Bit the bullet today and Ordered a new Galv. chassis today. TBC......
Bit the bullet today and Ordered a new Galv. chassis today. TBC......
lcbandit
Well-Known Member
- Posts
- 1,548
- Location
- west yorks
put some air in the front tyre but think its handling like a bag of **** cos the back of it is full of carpet tiles!!!
Big Mat
Well-Known Member
- Posts
- 943
- Location
- King's Lynn, Norfolk
Got pulled over again
Grow a beard, it works for me!
lcbandit
Well-Known Member
- Posts
- 1,548
- Location
- west yorks
Just fitted a disklok to it
mikescuba
Well-Known Member
- Posts
- 2,731
- Location
- France, Loire, Rhone Alpes
I don't know what came over me. I gave mine a thorough clean, fist the T-cut then a coat of polish. I should take a pic before it gets dirty again.
Sirus
Your all Banned except me
- Posts
- 22,196
- Location
- The Country of Black
Took it for its Mot after changing the back box and hangers and replacing the anti roll bar bushes and draglinks. It passed.
ratty
I'm not special I'm limited edition
- Posts
- 34,277
Nice one mate.
My MOT is out in the next couple of weeks so I rekon I'm gonna have to give it a once over tomorrow.
In the mean time I bought a toolbox grill to go in the back of it.
Sirus
Your all Banned except me
- Posts
- 22,196
- Location
- The Country of Black
Nice one mate.
My MOT is out in the next couple of weeks so I rekon I'm gonna have to give it a once over tomorrow.
In the mean time I bought a toolbox grill to go in the back of it.
Apparently me drop arm ball joint is going. Its only the 3rd one in about 500 miles. Oh and the fog light bulb decided to blow when I got there. Everything else was fine. Not too bad as it aint moved for about 12 months.
ratty
I'm not special I'm limited edition
- Posts
- 34,277
Apparently me drop arm ball joint is going. Its only the 3rd one in about 500 miles. Oh and the fog light bulb decided to blow when I got there. Everything else was fine. Not too bad as it aint moved for about 12 months.
I need to replace the track rod ends on mine before its mot. I'm wondering about changing the frop arm ball joint at the same time. My drop arm ball joint is about 2 1/2 years old as are the track rod ends.
Sirus
Your all Banned except me
- Posts
- 22,196
- Location
- The Country of Black
