Vagrent
Yaaaar
- Posts
- 18,109
- Location
- Poiret West Sussex, Chichester.
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
After removing all of the seats, stripped out the dry carpet only to find the soaking wet soundproof! Binned the whole lot!!
Treated the surface rust and coated the whole floor with a plasticized paint for 3 layers... Stinks a bit but but looks OK. No more worries with the standing water (as long as no where else leaks)...
Removed the EGR and inlet hose. Seriously gunked up hose so it was a good job it all went in the bin!
Not too bad for 2 days work - seen as i've NEVER worked on a car\engine before... Feeling smug now that it all works again and looks good...
Serious Beers tonight now!!!
Treated the surface rust and coated the whole floor with a plasticized paint for 3 layers... Stinks a bit but but looks OK. No more worries with the standing water (as long as no where else leaks)...
Removed the EGR and inlet hose. Seriously gunked up hose so it was a good job it all went in the bin!
Not too bad for 2 days work - seen as i've NEVER worked on a car\engine before... Feeling smug now that it all works again and looks good...
Serious Beers tonight now!!!
spent 4 hours tryin to get the brake lights workin.....eventually ran a new wire from the switch to the lights...fitted me fire extinguisher again and fitted an internal light...which just went pop ffs 
and flushed out me radiator and drunk beer so not a total loss !
and flushed out me radiator and drunk beer so not a total loss !
Trewey
Cockernee, Pasty munchin bastid.
- Posts
- 20,088
- Location
- Kernow - Near England
Finally got round to fitting me Rock Sliders (Thanks Ian Notts ? Axletwister 4x4).
Got one problem though - had to grind off one of the bulkhead bolts. Don't suppose anybody's got one I can have? It's off the road till I can replace it.
Top left of the pic...
Got one problem though - had to grind off one of the bulkhead bolts. Don't suppose anybody's got one I can have? It's off the road till I can replace it.
Top left of the pic...
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
If yu tell me length & diameter I probably will have one.
300TDI-Disco
New Member
- Posts
- 135
And nice they do look aswell
Trewey
Cockernee, Pasty munchin bastid.
- Posts
- 20,088
- Location
- Kernow - Near England
Tis 7 an arf inches long and takes a free quarter inch socket (or 19mm if yer a bodger).
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
M12. then If I Int got one I can pop to me local fasteners place in the morn and grab one place is an Aladdin's cave of nuts bolts shackles tools etc and very very cheap.
Trewey
Cockernee, Pasty munchin bastid.
- Posts
- 20,088
- Location
- Kernow - Near England
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Hoping to get down in July But I'll post ya bolt up to ya. Tomorrow. .
.
baggyjim
New Member
- Posts
- 2,063
- Location
- gillingham dorset
I likes wentin as well
ratty
I'm not special I'm limited edition
- Posts
- 34,277
walked past mine twice.
90truckcab
Well-Known Member
- Posts
- 4,739
- Location
- staffordshire
leaned against the series 2 , burned me arm on the wing got in the ser3 to move it an burned me hands on the steering wheel, couldnt get in the 90 it were boiling me back stuck to the seat ... am out welding up a chassis today in the sun. tis a killer , its beer garden weather !
got in the ser3 to move it an burned me hands on the steering wheel, couldnt get in the 90 it were boiling me back stuck to the seat ... am out welding up a chassis today in the sun. tis a killer , its beer garden weather !
Kernow nige
New Member
- Posts
- 1,286
- Location
- Landyless in KERNOW
Dropped mine in to local indie fer service an MOT!!
Plan, Plan, Plan,
working in dubai for four months so sorted out plan of atack for a body off rebuild, replace tired and naffed 19j with 200tdi, and maybe a nice galved chassis,
have not done a budget yet, dont want to cry.
donations welcome. lol
driving ford rangers makes me miss my 110
working in dubai for four months so sorted out plan of atack for a body off rebuild, replace tired and naffed 19j with 200tdi, and maybe a nice galved chassis,
have not done a budget yet, dont want to cry.
donations welcome. lol
driving ford rangers makes me miss my 110
twodoor
New Member
- Posts
- 35
- Location
- South Australia
A) Emptied the back end out and measured up for my cargo drawer plans....
B) Cut the carpet and removed the cargo tie down hoop thingies...
C) Removed the R/N/S cargo box....
B) Cut the carpet and removed the cargo tie down hoop thingies...
C) Removed the R/N/S cargo box....
TheMunster
Active Member
- Posts
- 357
fitted new steering box, steering shaft and drag link ball joints...fecking box wasn't straight!! ahhhh need to get the drop arm off now bollocks
