What have you done to your Landie today.

bigvinnie · Mar 26, 2014

Nothing was to busy driving to Fort george and back to collect these 2 pieces of crap Pinz,s and drop of at Stirling

Mac76 · Mar 26, 2014

Found a Hole in the rear of the chassis that waxoil was covering

discomark10 · Mar 27, 2014

MaxyMan said:
Just been looking at front 4link set ups for me flexing wagon, nearly had a heart attack. The bank account deffinetly wouldn't like it. Maybe if ah win the lotto?

Not cheap at all!

Not sure if a 3 link would be any less?

Looking to start my 1 link soon, I'll post lots of pics n info so it can be copy'd

MaxyMan · Mar 27, 2014

How are you planning on doing a 1 link matey?? Can't see how it would work lol

discomark10 · Mar 27, 2014

its like a radius arm setup but only 1 in the middle rather than 2 at either end, works well with 0 flex restriction

fanatic · Mar 27, 2014

It sends me a message saying where it is

Paul D · Mar 27, 2014

Almost finished the snorkel to me 90.

Still some work to do, but no time now as I have to get back to work .. just a bracket to make and sealing joints before finally tightening it all up ..

http://www.landyzone.co.uk/lz/2998405-post70.html

the_wolf · Mar 27, 2014

bigvinnie said:
Nothing was to busy driving to Fort george and back to collect these 2 pieces of crap Pinz,s and drop of at Stirling

And ya never popped in to say hello? I'm disappointed

. Many a time I've stopped off at that very spot anaw lol

the_wolf · Mar 27, 2014

Did this so's I can fold the windscreen down easily if the sun stays out for long enough

. Not the neatest job but it will do for now

a2dds · Mar 27, 2014

This morning I towed a friend to work in his 90 after he ran out of fuel. Pilock.

He hasnt had much luck, hasnt been on the road for long, had it on its side, snapped two fan belts too which is odd. tis a 19j though

:rolly:

trax · Mar 27, 2014

a2dds said:
This morning I towed a friend to work in his 90 after he ran out of fuel. Pilock.

He hasnt had much luck, hasnt been on the road for long, had it on its side, snapped two fan belts too which is odd. tis a 19j though :rolly:

first dibbs on the wheels when he breaks it

Mylz95 · Mar 27, 2014

Started the installation of my homemade electronic immobilizer

a2dds · Mar 27, 2014

trax said:
first dibbs on the wheels when he breaks it

Ha scavenger.

ebbadger · Mar 27, 2014

got the front ally door tops stripped and sprayed on the inside...

and got the lower doors sorted with a bit of knifing putty to sort the last few blemishes...

doesn't seem much but body prep is so long winded.. arghhh

Cheers Steve

MaxyMan · Mar 27, 2014

So all done tinkering today.
Fitted front flex kit, 14" shocks& turrets.
Bent a 3ft breaker bar holding the weight of the landy up on a trolley jack trying to undo front radius arms nuts on axle end.
What an arse they was to get off.
Why oh why previous owners can't use copper slip!!!!

MR BFG · Mar 27, 2014

On my way home decided to go up a local lane and when I climbed to the top saw steam out of the heater intake, so opened the bonnet had a look and zero coolant in the engine. Bugger.

Turns out heater matrix is split somewhere and the coolant is escaping from there, disconnected both heater pipes and joined them together. Jobs a good'un. At least when the heater box is out I can sort the snorkel out and weld up the bulkhead.

Racandy · Mar 27, 2014

Fitted an allbright solenoid as standard can types were sticking. Can tell massive difference already and stopped my headlights keep falling out when I go offroad. Earlier in the week I've cut arches and fitted flexi arches. Fitted spacers and done loads of welding. Still got sills to lol at yet

bigvinnie · Mar 27, 2014

the_wolf said:
And ya never popped in to say hello? I'm disappointed . Many a time I've stopped off at that very spot anaw lol

wolf if I had ken'd yu wur in work I would of looked for you. But the large stout man on the gate wasn't very helpful and trying to drive round the Dsg site aint the easiest...small location....I drove into the MAN SV yard unloaded and got going, long 2 days driving....where are you fur next time?

Morganholidayman · Mar 27, 2014

What have I done today?
Had major success with solving misfire/surging under load!!
You guys probably already done this but bought my 90 in Nov last year and after reading various notes about problem I looked at the injector cable conn for any oil in plug, none.
Decided to look at the turbo waste gate, yep seized solid. WD40 a plenty but no movement.
Thought I'll take heat shield off, two top bolts easy but one underneath a bugger!
Drilled out two pop rivets facing offside and prepared to grind off heads of rear facing rivets, but hey presto the bracket was already broken and it came away!
By this time the WD was working and took spring clip off link to vac can and slowly able to move the waste gate.
Eventually I could move lever easily. Boxed it all up again and used self tap screws for heat shield to Brit as think I might WD once a month!
Took it for a drive and whoa! Pulls under load like a train now.
Many thanks for all previous notes about misfire/surging, it really works!

Midway · Mar 27, 2014

Spent a few bob on my fender the day after pay day. New wing, drop link arm brake hoses, door top, locks and the list goes on.

What have you done to your Landie today.

Active Member

Attachments

New Member

Well-Known Member

Well-Known Member

Well-Known Member

RESPECT IS EARNED, BEATINGS ARE FREE ;-)

Old, nackered 'n broke, but the Landy is fine . :)

Well-Known Member

Well-Known Member

Attachments

Active Member

.

Member

Active Member

Well-Known Member

Well-Known Member

Active Member

New Member

Active Member

Member

New Member

Similar threads