What have you done to your Landie today.

Dippypud · Sep 23, 2013

Put a noo eggsauce on it ...

eventually ....

brian47 · Sep 23, 2013

I had always said that I was getting a bit long in the tooth for lying in the gutter under a vehicle, but there are some jobs it's just not worth going to a garage for.

Three jobs done today:

1. The window regulator in the driver's door was playing up; clunking like gears jumping out of mesh at the top and bottom of the travel and being able to pull the window down about four inches by hand. Removed the door trim, cut my way into the water screen and found that the winder motor and regulator which should have six bolt fixing it to the door only had three. Rummaged around in the bottom of the door, found the missing bolts and refitted them. Plenty of gaffer tape to make good the water screen and refitted the door trim. Window is now working within expected parameters.

2. Fitted a new front prop shaft. The original had a small amount of play at the axle end, I could barely feel it but it's there, either in the UJ or the sliding joint. I looked at repairing the original unit but working on the premise that I would have to remove it either way and the parts to rebuild it were about 60 quid, plus the fact that I don't have the kit to use as a press to do the rebuilding I decided to bite the bullet and get a new unit with the extra grease nipples on the double cardan joint as well as the UJ at the axle end. Grease up and fitted, all OK.

3. While I was in the mood and on a roll, I decided to grease the rear prop shaft too. Encountered the usual problem of having to get the shaft turned to just the right spot so that the grease gun nozzle went onto the nipple deep on the UJ, but it all went OK too. (Note to self. Replace nipple with a longer one next time.)

All-in-all a good day and well pleased.

pontyslapper · Sep 23, 2013

Know both places.

One is the BOAT on Eglwysilan, the other is a well used off piste route probably entered where an ex girlfriend used to live and just up the road from ours.

timtheenchanteruk · Sep 24, 2013

bought meself some noo spots for the light bar, some wind deflectors (and a couple of UJS) and another couple o stickers.

Dr_evil · Sep 24, 2013

collected its new radiator and checked up on some parts

Dr_evil · Sep 24, 2013

brian47 · Sep 24, 2013

Why do we need to know the size of a 2 pence piece?

bankz5152 · Sep 24, 2013

Found that my starter motor is gone AGAIN! 3 times in a year!!

landowner · Sep 24, 2013

The 'Black Duck' is now all sanded off almost ready for top coat of blue

Nice day tomorrow I hope, painted new rear door today and the wind got up and blew bits of crap on it

Few more tweaks and its ready for paint, its only a Landy after all

Dr_evil · Sep 24, 2013

Found some stainless manifolds near me

may as well have a bid I suppose

be rude not to really given they're only 25 mins away

the_wolf · Sep 24, 2013

bankz5152 said:
Found that my starter motor is gone AGAIN! 3 times in a year!!

You haven't been buying ****part ones have you? I hear they're made from chocolate.

Either that or something else is wrong

Chrisw8 · Sep 24, 2013

took my wheels to be powder coated. will post piccy when they come back.

neff · Sep 24, 2013

Been busy this week... checked off things to do before the MOT, picked up some new wheels and rims for Yogi and got through the MOT with no advisories... which was good!

Pikey · Sep 24, 2013

finally got round to getting the O/S front tyre changed over. After 3months of a slow puncture, 2 cans of tyre weld and a daily visit to the air pump, finally weren't enough. So took the spare tyre off the steel spare and had it put on the front alloy, & picked up me reserve spare from the workshop.

Only charged £15 to remove both tyres fit the good one balance it and dispose of the old tyre.

Dan_Trials · Sep 24, 2013

redhand said:
finally got round to getting the O/S front tyre changed over. After 3months of a slow puncture, 2 cans of tyre weld and a daily visit to the air pump, finally weren't enough. So took the spare tyre off the steel spare and had it put on the front alloy, & picked up me reserve spare from the workshop. Only charged £15 to remove both tyres fit the good one balance it and dispose of the old tyre.

£15 is a very good price.

I removed the trailing arm lower bushes using the drill and hacksaw method, wasn't that bad actually, had the brother in law round so we took it in turns to attack it and seemed to go quite quickly. Then wire brushed and rust converted them, now hanging in the garage drying.

Vic52 · Sep 25, 2013

Dreamed of what I'm going to do to it when I get back home next week

Not that kind of dream ye dirty barstuards. I have to replace the rear hight sensors for the air system. The links sort of rotted away

SimonThomas · Sep 25, 2013

. . .mine has had another polish this evening, I only did it Saturday!!!

pontyslapper · Sep 25, 2013

Parked it in a quite posh school car park in amongst some pretty new and expensive metal - Looked hard as fook, all muddied and scruffy in amongst the new tin.

Don't think the dainty little teacher creature was happy mind to find her brand shiny noo Fiat 500 overshadowed by a scabby '98 disco!

The kids thought it were ace - tidy! :banana:

:crazy:

the_wolf · Sep 25, 2013

Any pics of the teacher? Was she doable?

pontyslapper · Sep 25, 2013

She were ok. No pics as Id like to work there again and I think that might have naffed that up.

What have you done to your Landie today.

Never Knowingly Understood

Well-Known Member

Brought a Landy to LZ11. Yay!!

Well-Known Member

Banned

Banned

Well-Known Member

Well-Known Member

Pensioner Pete

Attachments

Banned

Well-Known Member

Well-Known Member

Member

Dummy Ejection Facilitator..

Well-Known Member

New Member

New Member

Brought a Landy to LZ11. Yay!!

Well-Known Member

Brought a Landy to LZ11. Yay!!

Similar threads