What have you done to your Landie today.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
drove it to scarborough for two day's R "N" R ..
 

Attachments

  • in the sun 004.JPG
    in the sun 004.JPG
    76.1 KB · Views: 190
  • in the sun 016.JPG
    in the sun 016.JPG
    41.5 KB · Views: 161
Last edited:
Chrisw8 said:
Hi Discomark.

I done that, but I can only get either 1 - 5 or 3 - 7. I cant seem to get it right across the range. Still, the ride is all flat tomorrow so I left it adjusted to 3 - 7. I'm wondering if my chain is stretched,
Click to expand...

sounds more like the sifter or selector is wrong for the amount of gears available rather than a chain problem.
 
Notice yesterday had a slight blow on engine. Well today found where it was blowing,bolt missing from exhaust to cylinder head is missing, the nearest one to front of engine. So now on hunt for new bolt
 
Towed some staging with it and sat there puzzled about the funny noise from my turbo.... cant spot a hole!
 
Swore at it lots, engine still smokes to much, cannot seem to fix it despite doing everything possible.

Considering taking it off the road now and getting a defender instead.
 
Cleaned up some rust on the battery box ready for painting, found holes. Guess I'm cutting tomorrow and welding then.

I really should stop looking for the rust.
 
Repaired my front Warn winch free spool. The thing was completely jammed up and could only spool out using the control, however a simple fix of removing the handle cleaning out the crap that had built up and giving a good spray of WD40 and putting back together sorted it right out :clap2:
 
Did another couple of hours on my electrics this evening. My new radio/CD came late this afternoon, so having read the instructions I ventured out to see if it would work in the car. Nothing's ever simple of course, and it remained stubbornly dead as the previous owners have done quite a lot of unorthodox rewiring. With circuit tester and multimeter I managed at last to get it working by pulling the pins out of a multiplug and putting them back in different holes. Only blew one fuse. Now I've discovered that whilst the passenger side speaker is nice and clear (after I located its wires and reconnected it) the speaker in the driver's footwell gives a lot of distortion. So I've ordered another.
 
Brown said:
Did another couple of hours on my electrics this evening. My new radio/CD came late this afternoon, so having read the instructions I ventured out to see if it would work in the car. Nothing's ever simple of course, and it remained stubbornly dead as the previous owners have done quite a lot of unorthodox rewiring. With circuit tester and multimeter I managed at last to get it working by pulling the pins out of a multiplug and putting them back in different holes. Only blew one fuse. Now I've discovered that whilst the passenger side speaker is nice and clear (after I located its wires and reconnected it) the speaker in the driver's footwell gives a lot of distortion. So I've ordered another.
Click to expand...

I did pretty much the same also, with a similar result! naffed drivers speaker!
 
Right O,

Today I had to make a mount for the trialers fuel tank and battery mount:





Frame in place ready to nail down.





Welding is getting better



Fuel tank mounted in and secured in:

 
Big Mat said:
2.25 derv, had top end rebuild after timing chain went wrong and smashed all push rods up, recon injectors and pump. Did all the timing but still cannot get the smoke down, not using any oil or anything, just smokes like a bugger underload. Clear tickover!
Click to expand...

If its not burning oil then obviously its burning too much derv. Try discconecting an injector at a time then testing, may be one is naffed. If not its more that likely the pump. Its running too rich for some reason under load. It may also be one cylinder is not burning right due to a valve, which is a lil harder detect unless you have a compression tester.
 
I've just stripped down the drivers door to find that the old metal moth has destroyed the window guide. I cant find a replacement on line (tried Flea Bay) has anyone any suggestions where I might get a replacement.
51 Plate discovery 2
Thanks
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
530
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
607
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
884
Knappster
Knappster
Mooky
Replacing thermostat
Replies
13
Views
460
dag019
dag019
I
Re-coding of ABS Module after repacement
Replies
10
Views
963
invisible999
I
Back
Top