What have you done to your Freelander today

Hippo · Jun 8, 2013

freelandie71 said:
They did check but I am not that optimistic just checked it again this morning and so far so good and the sun is out so I am of to town and give it an other blast

MHM is right. When they start to pressurise the system they will see the pressure going up. If they don't see the pressure go up they will stop and look for a leak, or advise it's leaking.

Freelaner · Jun 8, 2013

drove it to Dovedale and went for a long walk, then drove it back via the ford at Tissington

dustmaker · Jun 9, 2013

changed the oil in the ird, changed the gearbox oil, de-cat the exhaust and went to install a ronbox vp37 then discovered that in the instructions the wires to the fuel pump are yellow and red/pink but the wires on the module are purple and brown so that has stumped me for now

Tempus Fugit · Jun 9, 2013

Had both VIS motors refurbished now fitted, much better.

Had AC re-gassed, much better

dustmaker · Jun 9, 2013

finished the vp37 install just need to finish setting it up but between the de-cat and the ronbox its just so much better to drive :biggrin1:

drturbo · Jun 9, 2013

Checked out the dreaded rust behind the tailgate handle, just the middle fixing has rusted, seems I'll need to make up a boiler plate around that and paint it up, all hidden by the handle luckily...

Hippo · Jun 9, 2013

Tightened up a nut holding the heat shield to the ird/gearbox. Tested ma new creeper thing.

johndog666 · Jun 10, 2013

Guitarjon; I,ll get a pic on for you.

Guitarjon · Jun 10, 2013

johndog666 said:
Guitarjon; I,ll get a pic on for you.

Cheers fella.

Nodge68 · Jun 10, 2013

Tempus Fugit said:
Had both VIS motors refurbished now fitted, much better.

Had AC re-gassed, much better

I did mine last year. As you say it makes a difference. I recently had to swap the plenum as i had a noisy power valve.

celt69 · Jun 10, 2013

Changed my 3 rear diff mount took around 1.5Hrs not bad considering never done one before.

sijwhite · Jun 11, 2013

MoT'd and had the Air Con regassed.

pmaxwell · Jun 11, 2013

richijones said:
Fitted power sockets in boot, 1 normal cig lighter type and 1 din type. Wired from power socket under cubby box with in line
fuse and led.

Have you got any instruction for how to do this?

Thanks.

dustmaker · Jun 11, 2013

cured my non functioning horn although got to say the wiring schematics for the freelander are poor, finally found the horn relay tucked up and hidden above the horn

Gibbo_GTI · Jun 11, 2013

Replaced the fuel pump in the rear wheel arch, running much better now lol

Freelaner · Jun 11, 2013

pmaxwell said:
Have you got any instruction for how to do this?

Thanks.

Fantastic first post

sijwhite · Jun 11, 2013

pmaxwell said:
Have you got any instruction for how to do this?

Thanks.

Here you go.

dougjoy · Jun 11, 2013

new track rod ends fitted and front brake pads

freelandie71 · Jun 11, 2013

Clean off the biggest bird **** I have ever seen. Rear door and window was just covered must have been one big bird with a severe case of diahorrea.

baggyjim · Jun 11, 2013

freelandie71 said:
Clean off the biggest bird **** I have ever seen. Rear door and window was just covered must have been one big bird with a severe case of diahorrea.

or a re-incarnated tratter boy

What have you done to your Freelander today

Lord Hippo

Landy Driver

Active Member

Well-Known Member

Active Member

New Member

Lord Hippo

Active Member

New Member

Well-Known Member

New Member

Active Member

New Member

Active Member

Member

Landy Driver

Active Member

Attachments

Member

Active Member

New Member

Similar threads