Hicap phill
Well-Known Member
- Posts
- 16,238
- Location
- Wiltshire
What have you done on your 90/110/130 today?
- Thread starter neilly
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
v8250
Well-Known Member
- Posts
- 6,872
- Location
- Deepest Darkest...
yes, thanks @Hicap phill ...cranked arms, wider angle et al. They're very well made with the 19mm adjuster, solid grease nipple and the unit as a whole feels made of better quality/denser steel.
doriz
Well-Known Member
- Posts
- 17,312
Stupid thing has kicked my arse again 
what should have been a simple oil change turns into a farce and I've lost interest. Can I get the drain plug out, no, have I got the space underneath to really get some purchase, no. MAP blow lamp on order as this is going to need heat. I've also noticed the radius arm bushes are perished anorl .
Do the radius arms require the bushes to be pressed in or can I get the shell bushes as a direct replacement?
what should have been a simple oil change turns into a farce and I've lost interest. Can I get the drain plug out, no, have I got the space underneath to really get some purchase, no. MAP blow lamp on order as this is going to need heat. I've also noticed the radius arm bushes are perished anorl .Do the radius arms require the bushes to be pressed in or can I get the shell bushes as a direct replacement?
Last edited:
Hicap phill
Well-Known Member
- Posts
- 16,238
- Location
- Wiltshire
Hicap phill
Well-Known Member
- Posts
- 16,238
- Location
- Wiltshire
Today I have drove mine to get to a place to have a walk
doriz
Well-Known Member
- Posts
- 17,312
I watched a Uboob video earlier that suggested an engineers vice will press the cotton reel bushes home without issue. Cheers for the reply
- Posts
- 9,095
- Location
- North Lincs
I tried and gave up. I bought a 12 ton press and they go in easy. If it wasn't for this stupid situation, you could have brought them overI watched a Uboob video earlier that suggested an engineers vice will press the cotton reel bushes home without issue. Cheers for the reply
doriz
Well-Known Member
- Posts
- 17,312
I tried and gave up. I bought a 12 ton press and they go in easy. If it wasn't for this stupid situation, you could have brought them over
Cheers, very kind offer. The bushes that looked perished earlier were radius to chassis, however, I'm not dropping the things out to just bush that end.
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
Changed the A frame bushes for polybush ones and steering uj's
v8250
Well-Known Member
- Posts
- 6,872
- Location
- Deepest Darkest...
Hicap phill
Well-Known Member
- Posts
- 16,238
- Location
- Wiltshire
Use pro flex
Hicap phill
Well-Known Member
- Posts
- 16,238
- Location
- Wiltshire
You can do the radius to chassis rubbers without removing the arms off the axle
mikerajjers
Well-Known Member
- Posts
- 1,467
- Location
- Bedford UK or Trnava SK
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
Britpart ones but hoping they will last they look fairly good and where an excellent fit.
bluedog333
Well-Known Member
- Posts
- 5,441
- Location
- Henley on Thames, Oxfordshire
Fitted stainless pistons to the front brakes. Actually quite straightforward, although I think I need to bleed the brakes again as they’re a bit soft.
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Lob 'em in the freezer, that helps if you only have a vice available..
If it a proper Record Vice that is, not a puny one with no balls!!!
If it a proper Record Vice that is, not a puny one with no balls!!!
callisr
Well-Known Member
- Posts
- 615
- Location
- Burton-on-Trent, Staffs
I changed the Panhard rod bushes and did an engine oil and filter change. Also did the fuel filter and air filter.
Had a general poke about but found nothing else to tinker with!
Had a general poke about but found nothing else to tinker with!
bluedog333
Well-Known Member
- Posts
- 5,441
- Location
- Henley on Thames, Oxfordshire
Rear dampers and ARB bushes yesterday. Discovered a nasty hole in a fookin awkward part of the chassis which is going to need some drastic fixing!
So after many lockdown weekends of work, my 90 project is nearly complete. New panels, doors, roof, side panels removed and replaced with heavy-duty hood sticks (new tan canvas and black bikini), new hinges, bolts, and washers (the right spec and sizes), re-wired (removal of meters of old, useless wires that were doing nothing), striped back, primed and spray painted in Cornflower blue (an old 2A colour so I was told)... and loads more stuff that I could list.
A few jobs left... compounding and polishing the paintwork, removing the lift (going back to stock), new wolf rims (probably white), and BFGs.
Might not be to everyone's taste, but that's the fun of these... you make them your own. Anyway, I would be interested in your thoughts, suggestions (good or bad). BTW this is the first time I have ever done a rebuild, and a driveway respray so please go gentle
The first pic is how I brought it (for just over £6k)
The second pic is what I did to tidy it up, while I decided what I wanted to do with it
The remaining pics are as it is now
A few jobs left... compounding and polishing the paintwork, removing the lift (going back to stock), new wolf rims (probably white), and BFGs.
Might not be to everyone's taste, but that's the fun of these... you make them your own. Anyway, I would be interested in your thoughts, suggestions (good or bad). BTW this is the first time I have ever done a rebuild, and a driveway respray so please go gentle
The first pic is how I brought it (for just over £6k)
The second pic is what I did to tidy it up, while I decided what I wanted to do with it
The remaining pics are as it is now
Attachments
Similar threads
