what have you buggered up on yer series today

90truckcab · Mar 28, 2010

put yer self some beer crates to one side then lean it on them wile yer get down , ffs yer like a woman with all theses issues

or tie it to a tree and use the rope to pull it clear of the gearbox, even that engine hoist tight to the top will lift it enough to move it out

G-man · Mar 28, 2010

as i said it int the liftin its where t lift it from? their int much to attach rope to that int gonna get damaged

G-man · Mar 28, 2010

right yer **** tekkin bastards! its off! ahv fooked me bad knee but it now sits behind the rear tub on the floor!

The Mad Hat Man · Mar 28, 2010

Why would yu want to leave your knee behind the rear tub on the floor?
Do yu have an artificial limb? And wot about the rest of yo leg?

G-man · Mar 28, 2010

ok let me re-phrase that......

the bulk head is off and its now on the floor behind the rear tub, in removing the bulkhead i have fooked up my bad knee!

better?

90truckcab · Mar 28, 2010

why yes it certainly was

yer do some moanin, whats gunna get damaged? it looks about ****ed any way

G-man · Mar 29, 2010

cheeky git!

right its monday! fooking raining again! oh to have a workshop

G-man · Mar 29, 2010

it stopped raining for about an hour so the engine and gearbox are now out

landybird · Mar 29, 2010

Series71 said:
adjusted the idling speed so it doesnt stall at junctions then snapped an exhaust manifold stud tightening up the pipe :doh:

ffs S71 you's a heavy handed bastid:doh:

youre cracking on with the dismantling bit G-man

i'll bet the rebuild don't go so fast

90truckcab · Mar 29, 2010

did yer lift the block and box as one g spot ?

G-man · Mar 30, 2010

landybird said:
ffs S71 you's a heavy handed bastid:doh:

youre cracking on with the dismantling bit G-man i'll bet the rebuild don't go so fast

yeah i know it wont as its gonna have some fabrication going with it

90truckcab said:
did yer lift the block and box as one g spot ?

aye tis a cumbersome lump when yer do it together but takes a lot less time!

G-man · Mar 30, 2010

90truckcab said:
did yer lift the block and box as one g spot ?

found the pictures

90truckcab · Mar 30, 2010

yer iv done a few like that ( more balanced tho)

its ok , but i prefer to split them now

G-man · Mar 31, 2010

i should have extended the arm to its fullest setting (1/2 ton mark) as it would have given me a little extra hight and saved the handbrake drum clumping the front crossmember, btw that crane has paid for its self now! i would suggest to anyone get a 2ton (note i said TON not TONNE) engine crane if you have the space and the money it saves so much hassle BUT the next big tool on the list is a gantry

90truckcab · Mar 31, 2010

make one yer self, i did , rsj , its long gon now but it wer a good solid one , only cost £90 in steel

G-man · Mar 31, 2010

i was thinking about just getting a load of I section and having a pop meself.... would give me reason to rebuild the garage roof higher too! then i could have it run from where the back of the landy is all the way to the back of the garage! brilliant for taking engines etc out (and moving heavy stuff in and out of the garage)

what have you buggered up on yer series today

90truckcab

Well-Known Member

G-man

BBQ king

G-man

BBQ king

The Mad Hat Man

Well-Known Member

G-man

BBQ king

90truckcab

Well-Known Member

G-man

BBQ king

G-man

BBQ king

landybird

New Member

90truckcab

Well-Known Member

G-man

BBQ king

G-man

BBQ king

90truckcab

Well-Known Member

G-man

BBQ king

90truckcab

Well-Known Member

G-man

BBQ king

Similar threads