That don't look good, could be a rough pulley wearing the edge of the belt hopefully, it's just a duff belt, can happen sometimes,
good luck.
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
good luck.
- Posts
- 33,600
- Location
- North Shropshire
Allegedly all but one was changed, the one left was in good order but i don't know which one or even if you can see them all without spending a week taking bits off every bit seems dependant on another being removed first
- Posts
- 33,600
- Location
- North Shropshire
Blimey, just watched some YouTube videos on replacing the main belt.. fan and fan shroud off, turbo bypass off, gearbox oil cooler drop, drain the coolant de-gas the AC.. fook that idea right off.. not doing all that in a couple of hours!!!
5 min job on the p38 to change the belt
5 min job on the p38 to change the belt
Scotiawhiskers
Well-Known Member
- Posts
- 877
- Location
- Manchester
You sure the shop actually changed the belt then, or just did bits to make it quieter / less obvious for a while to get rid of you?Blimey, just watched some YouTube videos on replacing the main belt.. fan and fan shroud off, turbo bypass off, gearbox oil cooler drop, drain the coolant de-gas the AC.. fook that idea right off.. not doing all that in a couple of hours!!!
5 min job on the p38 to change the belt
- Posts
- 33,600
- Location
- North Shropshire
The invoice says both were replaced by pretty sure i checked at the time and the both looked new
That's modern motors for yer, P38 was easy mainly because they put the tensioner in a sensible place but, the design went back to the 90s before, the acccountants didn't consider or care who has to service/repair them, all they think of is £££, got similar on my Focus, hoping to change the thermostat tomorrow, alternator has to come off to make it easier, I'm too bloody old to struggle,Blimey, just watched some YouTube videos on replacing the main belt.. fan and fan shroud off, turbo bypass off, gearbox oil cooler drop, drain the coolant de-gas the AC.. fook that idea right off.. not doing all that in a couple of hours!!!
5 min job on the p38 to change the belt
got myself a set of them extra long ring spanners, I mean who in their right mind would put the belt tensioner at the bottom of
the engine? but, with the long spanner I won't need to lay on the cold wet ground.
Bad news is the front small belt has to come off, that has to be cut and put back on with a special stretch tool (pinch of salt needed).
But will look again tomorrow.
J
- Posts
- 33,600
- Location
- North Shropshire
Even more reason to let the garage sort it.. as far as I'm concerned, the original issue hasn't been fixed
I've just had another look at your photo, the AC compressor (I think that's what it is) pulley, looks damaged on the front edge.
Scotiawhiskers
Well-Known Member
- Posts
- 877
- Location
- Manchester
Maybe they changed the short belt instead and that is damage that has been there for longer on the big belt?
- Posts
- 33,600
- Location
- North Shropshire
You mean the nut? That's the viscous fan, it's been attacked with a chisel or similar at some point
- Posts
- 33,600
- Location
- North Shropshire
I'm 95% sure they changed both
- Posts
- 33,600
- Location
- North Shropshire
Sorry, can see it bottom right, can't see damage though, just a bit of orange rust? Where i cleaned some crap off
I thought it looked like the front edge of the groove was flattened off a bit, like it had been clouted with something, look to the
left of the centre of the pulley above it, maybe it's an illusion.
- Posts
- 33,600
- Location
- North Shropshire
I think i see what your mean but might just be the light was using flash. Will have a look tomorrow again, it's not moved since that pic
Ah, that would explain the illusion, fingers crossed.
Garage will probably say its something else to try and get out of it but worth a try.
J
- Posts
- 33,600
- Location
- North Shropshire
fer flip sake..
just tried to get into my p38, the door handle has broke and wont open from inside or outside
just tried to get into my p38, the door handle has broke and wont open from inside or outside
Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
That'll teach you to relegate the P38 to second place, it's sulkingfer flip sake..
just tried to get into my p38, the door handle has broke and wont open from inside or outside
- Posts
- 33,600
- Location
- North Shropshire
guessing the door card doesnt come out without damage.. i can get into the car, just no way to open the drivers doorThat'll teach you to relegate the P38 to second place, it's sulking
