- Posts
- 19,287
- Location
- Buckinghamshire, UK. ('95 DT)
Has no serious effects on them at all, until they interact with a coffin dodger. Let them get on with their lives.
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Has no serious effects on them at all, until they interact with a coffin dodger. Let them get on with their lives.
- Posts
- 58,170
- Location
- Preston Lancs.
No not only young people. Look at the demographic of all the places back in lock down.
- Posts
- 19,287
- Location
- Buckinghamshire, UK. ('95 DT)
A bit darker than the average Brit?
- Posts
- 58,170
- Location
- Preston Lancs.
Exactly.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Not quite what he means,but I do agree with you about pubs and now a discount at restaurants !
The lunitics have taken over the asylum. Personally I won't be going near any pub until the Pigs are back at their trough i.e.the M P's are back in the House of Parliament. 
Tricky of York
Well-Known Member
- Posts
- 616
- Location
- York
Hi All, took my son out for a drive to clear the cobwebs and ended up doing about 60 miles around the Yorkshire Wolds. What a blast, found some great lanes and spotted some footpaths for another day. Don’t you just love it when these beauties are on point. Next job fit the black badges I sprayed last week. Have a great weekend all.
Tricky
Tricky
- Posts
- 2,427
- Location
- Isle Sheppy
Still trying to undo these poxy ball joint nuts it’s loose but not going any further down the thread
Tricky of York
Well-Known Member
- Posts
- 616
- Location
- York
Mrs Tricky and I worked on that for hours, she came up with some other suggestions for what it should be called but I explained we only have these letters for each end of the car.
Tricky.
- Posts
- 19,287
- Location
- Buckinghamshire, UK. ('95 DT)
Grinder time. All mine were just cut off and replaced.
- Posts
- 2,427
- Location
- Isle Sheppy
I’ve just cut the bolt off still no joy so now for the nut I was just thinking of the length of the bolt for pushing it out that’s all but will persevere
Tenebreaux
Well-Known Member
- Posts
- 4,284
- Location
- Armagh
New glow plugs in. That last electrical connector nut at the front is a total sod. Much use of my magnetic picker upper gizmo.
- Posts
- 2,427
- Location
- Isle Sheppy
Next job got to get 32mm spanner for lock nut on ball joint now to get the abs sensors out and replace any suggestions much appreciated part number ftc2249
- Posts
- 19,287
- Location
- Buckinghamshire, UK. ('95 DT)
ABS sensors just pull out. They'll be in a sort of springy bush that should have a lip you can lever up.
Datatek
Well-Known Member
- Posts
- 44,849
- Location
- Near Poitiers SW France
- Posts
- 2,427
- Location
- Isle Sheppy
Got the copper inserts out but not the bigger grommet things any suggestions
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Photos always help.
Gord Wedman
Well-Known Member
- Posts
- 617
- Location
- Chilliwack, British Columbia
"Service Engine Soon" light came on the other day so got out the Hawkeye Total to have a look and it turned out to just be the SAI which has not been working correctly for a while. I have checked all the vacuum lines and replaced with a good set from a parts car but no change. Not worried about it as the car runs fine. While looking at live data out of curiousity I noticed the alternator was only putting out 12.9 volts which is not too good so I decided to take my spare to the local auto electric shop for a check out. The $10 test indicated it would put out 144 amps at 14.4 volts so that sounded like something I needed to swap in. I decided to also install the new belt tensioner and idler pulleys that I bought last year.
Removed the plastic guards over the belts and also disconnected the upper rad hose from engine and radiator to move it aside. Next step was to move the belt tensioner to allow slipping the belt off the alternator pulley. In my experience belt tensioners usually have a square hole into which you fit a belt tensioner wrench which is just a long flat bar with a square nub at the end. The one on the P38 does have this but it is obstructed by the alternator mounting bracket so you have to use a 16mm box end wrench on the bolt that holds the tensioner pulley in place to pry up the tensioner and release the belt. I had to put a short pipe on the wrench to get enough leverage. After slipping off the belt I tie it back with a bungy cord. There are two long bolts holding the alternator in place. Once removed you can pry up the alternator to release it. I did not disconnect the battery but very carefully removed the positive lead and put the end in a doubled up plastic bag. Just be carefull you don't touch the engine with your wrench or ratchet (I hate trying to reset my sunroof so don't like disconnecting the battery). Next step was to remove the small idler pulley below the tensioner using a 13mm wrench. A bit awkward with the fan in place but can be done. Once this pulley is off you can use a 13mm socket and rachet to remove bolt that holds the tensioner in place. Install the new tensioner and idler pulley. Last step is to replace the large idler pulley on the opposite side of the engine which is easy to do. Alternator is easy to refit if you tap the steel inserts to make sure they are all the way over in the aluminum bracket. Final result was 13.9 to 14.1 volts at idle. Now if I could get rid of that SAI related light....
Removed the plastic guards over the belts and also disconnected the upper rad hose from engine and radiator to move it aside. Next step was to move the belt tensioner to allow slipping the belt off the alternator pulley. In my experience belt tensioners usually have a square hole into which you fit a belt tensioner wrench which is just a long flat bar with a square nub at the end. The one on the P38 does have this but it is obstructed by the alternator mounting bracket so you have to use a 16mm box end wrench on the bolt that holds the tensioner pulley in place to pry up the tensioner and release the belt. I had to put a short pipe on the wrench to get enough leverage. After slipping off the belt I tie it back with a bungy cord. There are two long bolts holding the alternator in place. Once removed you can pry up the alternator to release it. I did not disconnect the battery but very carefully removed the positive lead and put the end in a doubled up plastic bag. Just be carefull you don't touch the engine with your wrench or ratchet (I hate trying to reset my sunroof so don't like disconnecting the battery). Next step was to remove the small idler pulley below the tensioner using a 13mm wrench. A bit awkward with the fan in place but can be done. Once this pulley is off you can use a 13mm socket and rachet to remove bolt that holds the tensioner in place. Install the new tensioner and idler pulley. Last step is to replace the large idler pulley on the opposite side of the engine which is easy to do. Alternator is easy to refit if you tap the steel inserts to make sure they are all the way over in the aluminum bracket. Final result was 13.9 to 14.1 volts at idle. Now if I could get rid of that SAI related light....
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Got a wave from another P38 on the way to work, a nice gold one..
- Posts
- 2,427
- Location
- Isle Sheppy
The bottom piece is the bit I’m trying to remove 
