What did you do with your Range Rover today

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
It got broken up this thread!
IMG_20191201_123420.jpg
so the new screws are almost identical to the old. Apart from the fact they are self tapping.. But not an issue.
IMG_20191201_123321.jpg

Out with old and on with the new!
IMG_20191201_124954.jpg
thus stuff can be cut with a good pair if scissors and formed by hand really easily.
IMG_20191201_125026.jpg

And using the original clips but not the rail for the sponge.
IMG_20191201_130031.jpg

And the flip side...
IMG_20191201_130942.jpg


IMG_20191201_132135.jpg
and there was 18 screws in the packet which replaced all of them including the pollen filter caps:cool:
IMG_20191201_132158.jpg

Just for reference to size and they screw in perfectly. ;)
 

Attachments

  • IMG_20191201_130038.jpg
    IMG_20191201_130038.jpg
    280 KB · Views: 94
Jon Dor said:
You say "... Imprezza"... I say "Imprezzive"! Is it straightforward to do it?
Click to expand...
Very easy with a pair of tin snips. I can give you a link to the perforated alloy I used which being flat fits using the wire retaining frame that held the foam. I also fitted it over the 2 end openings where there was no foam, that needs a couple of self tapping screws. I posted some photo's I think but as the search is not working I can try to find them and re-post if you wish.
 
Datatek said:
Very easy with a pair of tin snips. I can give you a link to the perforated alloy I used which being flat fits using the wire retaining frame that held the foam. I also fitted it over the 2 end openings where there was no foam, that needs a couple of self tapping screws. I posted some photo's I think but as the search is not working I can try to find them and re-post if you wish.
Click to expand...
Thanks for your kind offer Datatek...look forward to receiving when convenient for you.
 
Mark Piercy said:
It got broken up this thread!
View attachment 195298 so the new screws are almost identical to the old. Apart from the fact they are self tapping.. But not an issue.
View attachment 195299
Out with old and on with the new! View attachment 195300thus stuff can be cut with a good pair if scissors and formed by hand really easily.
View attachment 195301
And using the original clips but not the rail for the sponge.
View attachment 195305
And the flip side...
View attachment 195308

View attachment 195309 and there was 18 screws in the packet which replaced all of them including the pollen filter caps:cool:
View attachment 195310
Just for reference to size and they screw in perfectly. ;)
Click to expand...
Looks good but harder work than using the flat stuff
 
Datatek said:
Very easy with a pair of tin snips. I can give you a link to the perforated alloy I used which being flat fits using the wire retaining frame that held the foam. I also fitted it over the 2 end openings where there was no foam, that needs a couple of self tapping screws. I posted some photo's I think but as the search is not working I can try to find them and re-post if you wish.
Click to expand...
I did the same and covered the ends as well. Seems daft to put sponge on the middle and leave the ends open..
 
Mark Piercy said:
It got broken up this thread!
View attachment 195298 so the new screws are almost identical to the old. Apart from the fact they are self tapping.. But not an issue.
View attachment 195299
Out with old and on with the new! View attachment 195300thus stuff can be cut with a good pair if scissors and formed by hand really easily.
View attachment 195301
And using the original clips but not the rail for the sponge.
View attachment 195305
And the flip side...
View attachment 195308

View attachment 195309 and there was 18 screws in the packet which replaced all of them including the pollen filter caps:cool:
View attachment 195310
Just for reference to size and they screw in perfectly. ;)
Click to expand...
Nice job, I put stainless steel screws all around
 
Tenebreaux said:
What I found was that Yamaha FS1E gearboxes are too small for all the bits to fit into. Some kind of Tardis effect going on, methinks.
Click to expand...
Fizzy gearboxes were easy! Only 4 speed.
Pain in the butt getting all the shafts to line up when you put case back together though!
Round file on the disc valve worked wonders for a bit more poke though!
 
Grrrrrr said:
Get yourself on LZIR!
Click to expand...
I can’t i have commitment issues. I’d make exception for certain people I guess. What good would it do when I sign in 11pm - they’d have walked back to Salisbury by then

Tenebreaux said:
What make was the OE battery in a 2000 P38 diesel? The one I replaced was a Lucas
Click to expand...
Lucas is as shyte as the original. They should all have a 1000cca 120ah type 31 imo. It just makes everything work properly and dependable. I stand by Datatek’s recommendation of batterymegastore.co.uk version. I bought the wrong one and it cost me a little extra.

Mark Piercy said:
Hmmm, after the wet passenger footwell and degraded sponge for the heater intake, decided to do this!!

OK, it's a little suburu impreza but being aluminum it's really easy to use.
Click to expand...
@Doo has the same stuff as that, is inside his vehicle too. I think it looks okay but I do prefer Keith’s.
 
Last edited:
You must log in or register to reply here.

Similar threads

A
Range Rover L322 - not turning over
Replies
12
Views
1K
gold rover
gold rover
B
L320 range rover sport 3.0 tdv6 loosing power steering fluid
Replies
3
Views
470
Mark Piercy
Mark Piercy
F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
1K
Grrrrrr
Grrrrrr
T
Non start
Replies
3
Views
709
Datatek
Datatek
T
Fan Clutch??
Replies
14
Views
775
Grrrrrr
Grrrrrr
Back
Top