What did you do with your Range Rover today

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Got EAS, pressure switch not changing state error 3 times today after ages without it. Travelling nanocom to the rescue.
What can we expect when we haven't sorted the seep through the roof yet and we go to the lake District?
 
Got it picked up by a friendly, free Land Rover experienced mechanic to sort out the engine timing and the worn out exhaust manifold bolt. oh, and finally install the Truetrac diff in the rear. Removed a hornets nest before he left, turns out if a dark, protected space is in the same spot for a year it becomes interessting as living space. Put said nest in a protected space to bot harm the queen over winter.

Good news, since I put sealant over all the joints around the gearbox, transfer case and engine she doesn't leak at all anymore!

She'll be back in a month or so for MOT!

Said to see the space in the drive way empty so...
 
I thought the change was 2007 for that.

dunno.
24th March 2006 was the significant date for that, no idea why it was on that day as I always thought that a 55 plate will be on the cheaper end but an '06 will empty your wallet a lot more but based on the Gov.uk website, you could conceivably get an '06 that is in the cheaper bracket provided it was registered in the first 23 days of March.

Petrol car (TC48) and diesel car (TC49)​

https://www.gov.uk/vehicle-tax-rate-tables/rates-for-cars-registered-on-or-after-1-march-2001
The detail is in line K. *Includes cars with a CO2 figure over 225g/km but were registered before 23 March 2006.
 
Wafted to the garden centre for lunch, then home via fuel. Considering the traffic and roads of the last week, quite happy with 19.8mpg for the last nearly 400miles. Snugged under his cover with the trickle charger and dehumidifier, having taken nearly 2 litres out with it during the last 5 days.
 
Change the L322 key fob case.

But becareful you don’t lose the little spring :oops:.

So it went from this. IMG_0846.jpegIMG_0845.jpeg

To thisIMG_0857.jpeg


1 down 1 to go.

J
 
MOT for the P38 today. Needed a new track rod ball joint as the play in the OS front wheel turned out to be that and not the bearing, phew! Once that was fitted and tested only one advisory was a lower suspension arm ball joint dust cover which when I asked about they advised to wait until it’s a real problem and would be a failure as apparently the upper will need to be done at the same time, and they’re a pig to do.
 
MOT for the P38 today. Needed a new track rod ball joint as the play in the OS front wheel turned out to be that and not the bearing, phew! Once that was fitted and tested only one advisory was a lower suspension arm ball joint dust cover which when I asked about they advised to wait until it’s a real problem and would be a failure as apparently the upper will need to be done at the same time, and they’re a pig to do.
Upper and lower swivel should be done together. Not such a bad job with the right tools which are not terribly expensive.
 
Would you mind pointing me in the right direction for the tools?
I'll have to go look but what I can get in France may not be the same as what is available in the UK. There have been several posts about the tolls for the job.
The worst part is getting the ABS sensor out, usually they have to be destroyed to remove them.
Link below shows the type of tool I used.
 
I'll have to go look but what I can get in France may not be the same as what is available in the UK. There have been several posts about the tolls for the job.
The worst part is getting the ABS sensor out, usually they have to be destroyed to remove them.
Link below shows the type of tool I used.
@P38Seb if you can look for the version with extra sleeves - it makes the job easier.
 
I'll have to go look but what I can get in France may not be the same as what is available in the UK. There have been several posts about the tolls for the job.
The worst part is getting the ABS sensor out, usually they have to be destroyed to remove them.
Link below shows the type of tool I used.
I’ve already had to turn on sensor into a liquid to replace it so I’m well versed in the ABS sensors.

Thanks for a link to the tools, I’ll take a look at Euro Car Parts to see what I can get.
 
Back
Top