gold rover
Well-Known Member
- Posts
- 10,240
- Location
- dùthaich Dhè fèin
Drove her to a field. Where I am currently sitting. Trying to trap a cat 
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 33,600
- Location
- North Shropshire
What you need is a cat trap!!
gold rover
Well-Known Member
- Posts
- 10,240
- Location
- dùthaich Dhè fèin
I have one, but this one is manual. The automatics are being used elsewhere
badfluffy
Well-Known Member
- Posts
- 2,132
- Location
- northampton
how many cats you after catching then?
gold rover
Well-Known Member
- Posts
- 10,240
- Location
- dùthaich Dhè fèin
At the moment we're after 3, but in different locations. It's a cat rescue I help with. Ferals are caught, neutered, and farms, or similar found for them. The little one I was after earlier is really young. If we get them young enough they can sometimes become pets.
Strays/abandoned are caught and taken to vet to be scanned and health issues sorted.
badfluffy
Well-Known Member
- Posts
- 2,132
- Location
- northampton
ah i see
- Posts
- 16,352
- Location
- Benfleet, Essex
Today I had a nice 90 mile drive in the old bus (P38), and despite all the traffic chaos and the sudden appearance of "ABS Fault/Traction Fault" (AGAIN) it was a nice uneventful drive.
- Posts
- 33,600
- Location
- North Shropshire
Any tricks to getting an abs sensor out? Or is destruction with mole grips the only way?
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Still rust busting!
- Posts
- 12,628
- Location
- Sud ouest France !
Gently with parrot grips and plenty of wd40 or the like. They can take some patience but some can take the biscuit!!! And it's murdering time
- Posts
- 2,427
- Location
- Isle Sheppy
Had to replace all mine they were originals so in there 20 years
- Posts
- 33,600
- Location
- North Shropshire
Argh!! New exhaust manifold gaskets, old ones evidence of leaking, new ones on!! Can still hear it blowing
And something is squeaking!! Sounds like fan belt, or maybe bearing.. but only hear it under load/heavy acceleration.. tensioner is ok, could it really be slipping? All bearings feel 'ok'
And something is squeaking!! Sounds like fan belt, or maybe bearing.. but only hear it under load/heavy acceleration.. tensioner is ok, could it really be slipping? All bearings feel 'ok'
- Posts
- 4,653
- Location
- Rotherham
This is mine rescued at 6mnths
Attachments
Flossie
Well-Known Member
- Posts
- 11,000
- Location
- Shropshire
I spent hrs on mine which, when I eventually gave up and got the hub in the vice, realised that they were never going to come out conventionally.
Feckers were welded in.
- Posts
- 4,653
- Location
- Rotherham
Used one of those windscreen repair kits yesterday on the MX5 on a stone chip. Blooming marvelous. £4.45 against the £40 insurance company wanted me to pay. If you don't know where it was you wouldn't notice the repair
- Posts
- 12,628
- Location
- Sud ouest France !
How was the manifold face? All clean and flat.. How did you bolt it back on?Argh!! New exhaust manifold gaskets, old ones evidence of leaking, new ones on!! Can still hear it blowing
And something is squeaking!! Sounds like fan belt, or maybe bearing.. but only hear it under load/heavy acceleration.. tensioner is ok, could it really be slipping? All bearings feel 'ok'
- Posts
- 33,600
- Location
- North Shropshire
- Posts
- 12,628
- Location
- Sud ouest France !
Ooer.. You may have a track worn Into the manifold face..Didn't take the manifold off just swapped the gaskets
I used the bolts i took off
With a manifold, I start to bolt from one side to the other or start from the middle outwards. That way you chase any tension out of the manifold.
- Posts
- 33,600
- Location
- North Shropshire
I bolted from the middle outOoer.. You may have a track worn Into the manifold face..
With a manifold, I start to bolt from one side to the other or start from the middle outwards. That way you chase any tension out of the manifold.
- Posts
- 12,628
- Location
- Sud ouest France !
It might be worthwhile pulling it off to check the faces...I bolted from the middle out
