- Posts
- 33,600
- Location
- North Shropshire
Like the one that's felled apart?Thats what i thought, whoooo muuuch
i have boxes of springs i got from my model enginnering club but really you need one that will not rust
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 33,600
- Location
- North Shropshire
Don't suppose you know the size? I'll have a look in the winter catalogue! Shouldn't be too different to the spring oneThats what i thought, whoooo muuuch
i have boxes of springs i got from my model enginnering club but really you need one that will not rust
brianp38dse
Well-Known Member
- Posts
- 20,063
- Location
- heathrow
Don't suppose you know the size? I'll have a look in the winter catalogue! Shouldn't be too different to the spring one
The spring is 34mm od, 42mm long and about 1.4mm thick 16 gauge wire.
- Posts
- 33,600
- Location
- North Shropshire
Thank you
Today is lpg injector day, found the seal that is leaking in the top of the injector, seems to be height adjustable but not sure why
Enthusiastman
Well-Known Member
- Posts
- 1,016
- Location
- AS LONG AS ITS NOT ****ING WALES!!!!
Deffo sounds like an electrical side problem with the LPG buddy. As i am no electrician i am now out of this. LOL. But as mentioned before matey, ANY decent LPG chap will be able to fault find and resolve it for you. I was lucky i suppose as all 3 of my duel fuel cars were 100% reliable and problem free. I just used to get my local LPG chap to check and service them annually for me. Cost me about £65 each year. No brainer for me. I am sure you will resolve it soon enough.
- Posts
- 33,600
- Location
- North Shropshire
Fixed my boot switch!! Just needed lubrication!!
However in my excitement i put everything back together and shut the boot without connection the wire!! Oops. Any ideas how i get back in?
You can laugh after
However in my excitement i put everything back together and shut the boot without connection the wire!! Oops. Any ideas how i get back in?
You can laugh after
- Posts
- 33,600
- Location
- North Shropshire
Read folks 'easily' get in from the inside, but don't see how without destroying the plastic flap that goes over the hinged gap when it's openFixed my boot switch!! Just needed lubrication!!
However in my excitement i put everything back together and shut the boot without connection the wire!! Oops. Any ideas how i get back in?
You can laugh after
- Posts
- 4,653
- Location
- Rotherham
Can't you get to the wiring from the inside. If not my mates got oxy acetylene cutting gearFixed my boot switch!! Just needed lubrication!!
However in my excitement i put everything back together and shut the boot without connection the wire!! Oops. Any ideas how i get back in?
You can laugh after
Is there not a manual release? On my 5 series theres a small oval plastic cover when you pull that out its attached to a cable that releases the catch
- Posts
- 33,600
- Location
- North Shropshire
Can't you get to the wiring from the inside. If not my mates got oxy acetylene cutting gear
No manual release and nanocom is no help either!
I can only see destroying the flap so far
- Posts
- 33,600
- Location
- North Shropshire
Too dark and cold now but MIGHT be able to slide the spare wheel cover under my lpg tank top remove the flap.. fingers crossedNo manual release and nanocom is no help either!
I can only see destroying the flap so far
- Posts
- 724
- Location
- Lincolnshire
If I remember right there’s 3 fasteners that secure the carpet board under the hinge flap. Will the flap not tilt a bit to give access?
- Posts
- 33,600
- Location
- North Shropshire
Yes 3 fasteners, but the flap only pulls away an inch max, hoping I'll be able to unscrew it if i can get the boot floor out of the way enough
- Posts
- 4,653
- Location
- Rotherham
Just check sure there's about 6 screws hold the flap in place. Pull it back have a look, fiddly but doable Will pop out and have a look on mine
- Posts
- 4,653
- Location
- Rotherham
Just had a look 3 fasteners once out you should be able to get cover off with a minimum of damage . Long thin screwdriver or similar should get fasteners out.
Have a drink and check again in morning. Know it has been done this way before
- Posts
- 33,600
- Location
- North Shropshire
Thanks! My difficulty is the lpg track against the back seat.. fingers crossed there is enough room
- Posts
- 4,653
- Location
- Rotherham
I know its gonna be fiddly but may the force be with you
One thing don't think you'll forget ever again
- Posts
- 33,600
- Location
- North Shropshire
I'm usually really good about things like thisI know its gonna be fiddly but may the force be with you
One thing don't think you'll forget ever again
- Posts
- 4,653
- Location
- Rotherham
A good man who ain't cocked up and admits it ain't a man in my books. I've done it many a timeI'm usually really good about things like this
