- Posts
- 19,284
- Location
- Buckinghamshire, UK. ('95 DT)
Heat the ****ers. Only way to get them out without a grinder.
What did you broked on your RangeRover today
- Thread starter RangeRoller dt
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Heat the ****ers. Only way to get them out without a grinder.
- Posts
- 19,284
- Location
- Buckinghamshire, UK. ('95 DT)
You didn't try to do it in-situ?
Tenebreaux
Well-Known Member
- Posts
- 4,280
- Location
- Armagh
After reading RRDT's woes I bought new guide pins anyway. So I just sliced straight through where the pin touches the caliper.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,385
- Location
- Trapped inside my head @ LZ asylum
Heat from drilling did as much as the actual drilling. To keep going while it was red hot was extremely beneficial
I still have the tan from that one
I still have the tan from that one
Tenebreaux
Well-Known Member
- Posts
- 4,280
- Location
- Armagh
Pins actually came out fairly easily. If it hadn't been for that one bolt it would have been a doddle.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,385
- Location
- Trapped inside my head @ LZ asylum
Same here 
one pin.
Where’s the pics of your rusted up hubs en? Mine were terrible but few coats of atf and thorough pecking with an nammer and chisel they came up good. Make sure your CV boots are on tidy while you are there
one pin. Where’s the pics of your rusted up hubs en? Mine were terrible but few coats of atf and thorough pecking with an nammer and chisel they came up good. Make sure your CV boots are on tidy while you are there
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
The brakes on mine were shocking..
One of the rear pads was worn to such excess it fell out when i was driving home..
should of taken that as a omen..
Weirdly the shíttest part of the car "engine" is the best working bit of the entire thing!!
Odd
One of the rear pads was worn to such excess it fell out when i was driving home..
should of taken that as a omen..
Weirdly the shíttest part of the car "engine" is the best working bit of the entire thing!!
Odd
Tenebreaux
Well-Known Member
- Posts
- 4,280
- Location
- Armagh
Hubs weren't too bad, wire brush cleaned off what was there. You saw the state of the calipers though. When the new ones arrive I'll put the carriers in the vice and hit them with the wire brush in the drill.Same here
Where’s the pics of your rusted up hubs en? Mine were terrible but few coats of atf and thorough pecking with an nammer and chisel they came up good. Make sure your CV boots are on tidy while you are there
Tenebreaux
Well-Known Member
- Posts
- 4,280
- Location
- Armagh
I haven't even looked at the rears. One disaster at a time, tyvm.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,385
- Location
- Trapped inside my head @ LZ asylum
^^^ Enerys were shockingly bad but they come up great. I didn’t paint mine and they still look decent. I am regretting not putting new pads in front while I was there, it braked fine even before the overhaul weirdly?? But it niggles at the back of my mind
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Tenebreaux
Well-Known Member
- Posts
- 4,280
- Location
- Armagh
Ouch.
- Posts
- 19,284
- Location
- Buckinghamshire, UK. ('95 DT)
That's what I did.
Attachments
Datatek
Well-Known Member
- Posts
- 44,838
- Location
- Near Poitiers SW France
It will be fine until the BECM decides enough is enough.
kds
Well-Known Member
- Posts
- 2,260
- Location
- old,ugly, tired in Lincoln.
SpaceX doing the delivery then ? (location, space just in case anybody wonders what I`m on about)
Salisbury Nick
Well-Known Member
- Posts
- 790
- Location
- Dorchester
Yup. That’s a bugger of a job.
Salisbury Nick
Well-Known Member
- Posts
- 790
- Location
- Dorchester
Funny the way some sockets fit perfectly and some don’t.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,385
- Location
- Trapped inside my head @ LZ asylum
Specially T55s
- Posts
- 19,284
- Location
- Buckinghamshire, UK. ('95 DT)
I think I would give that a little squirt of Plusgas every few days in the hope that when you finally get around to opening it, some may have got through. Think we're looking at a blowtorch too.
Either that or get a quote and let it be someone else's problem!
Similar threads
