Classic VM 2.5 to 200tdi swap - LT77 bell housing

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
P

portokali

Member
Posts
37
Hi All,
I recently pulled apart my VM on 1991 RRC and it's in a very sorry condition 😢. All parts are extremely worn and have decided to scrap it for a 200 tdi due to part cost and reliability.
I have a 200 tdi from a defender with radiator, intercooler etc.
However I want to know if the LT77 suffix G on my RRCwill fit the 200 tdi with the VM bell housing.
If you have done such a swap can you share what you did? Thank you!
 
portokali said:
Hi All,
I recently pulled apart my VM on 1991 RRC and it's in a very sorry condition 😢. All parts are extremely worn and have decided to scrap it for a 200 tdi due to part cost and reliability.
I have a 200 tdi from a defender with radiator, intercooler etc.
However I want to know if the LT77 suffix G on my RRCwill fit the 200 tdi with the VM bell housing.
If you have done such a swap can you share what you did? Thank you!
Click to expand...
Ask Ashcroft.
Well worth doing the rear main on the 200 before fitting, genuine only.
 
portokali said:
Hi All,
I recently pulled apart my VM on 1991 RRC and it's in a very sorry condition 😢. All parts are extremely worn and have decided to scrap it for a 200 tdi due to part cost and reliability.
I have a 200 tdi from a defender with radiator, intercooler etc.
However I want to know if the LT77 suffix G on my RRCwill fit the 200 tdi with the VM bell housing.
If you have done such a swap can you share what you did? Thank you!
Click to expand...
I'd stick with the VM. They were used in lots of other vehicles. They also go better than a Tdi.
 
Thank you. I've decided to go with 200 tdi so no more VM. To rebuild is $2500 + labor so it doesn't make sense.
I looked up on Ashcroft and a special spigot bush and clutch friction plate, STC1166 and However it's not clear it a new bell housing is needed or not? Thank you!
 
portokali said:
Thank you. I've decided to go with 200 tdi so no more VM. To rebuild is $2500 + labor so it doesn't make sense.
I looked up on Ashcroft and a special spigot bush and clutch friction plate, STC1166 and However it's not clear it a new bell housing is needed or not? Thank you!
Click to expand...
What country are you in?

Are you paying for the conversion too? Can't see that working out any cheaper.
 
300bhp/ton said:
What country are you in?

Are you paying for the conversion too? Can't see that working out any cheaper.
Click to expand...
Thanks! I will be converting it myself with support from a shop. I don't have confidence in the VM and the estimate only includes the top end heads, cylinders, rings etc. with pistons and any bottom end work cost/benefit doesn't make sense.
 
I did this many years ago on my 89 RR , I used engine and box out of a discovery as the box input shaft is different on the VM think defender turbo is in different place to the disco and had to make and weld on new engine to chassis mounts.
 
kds said:
I did this many years ago on my 89 RR , I used engine and box out of a discovery as the box input shaft is different on the VM think defender turbo is in different place to the disco and had to make and weld on new engine to chassis mounts.
Click to expand...
 
That's what I've found as well. The input shaft is different. However I don't know if it's just diameter or also length. Ideally I can reuse the VM LT77 as finding a discovery one here is tricky.
 
You must log in or register to reply here.

Similar threads

R
Range Rover Classic 2.5 VM diesel starter motor problem
Replies
6
Views
2K
frog hopper
frog hopper
P
Advice needed for fixing a VM 2.5
Replies
9
Views
2K
lynall
L
M
Engine swap, 2.5vm out and 200tdi in
Replies
15
Views
3K
300bhp/ton
300bhp/ton
R
Range Rover classic bell housing
Replies
1
Views
815
kds
K
M
Discovery1 lt230 in place of LT230R from a 12D?
Replies
3
Views
887
MrF
M
Back
Top