Vibration

jaylewis29 · May 24, 2008

hi im new to all this so ill say hello and get on with it

ive recently bought a landrover freelander on a w(2000) plate nearly everything is fine, apart from when driving, @ 3000rpm on every gear change there is a vibration @ 3500rpm it gose away it feels like its coming from the middle (prop) but i know these things can be deciving, its bloody frustrating

trying to get a smoothe ride, so the moral is any advice or help from any 1 would be greatfully appreciated thanks ......... jay

chuts · May 24, 2008

I have the same problem, everytime I switch my radio off I can hear a new creak or groan so tend to leave it switched on. Think its just a freelander thing

faureb · May 24, 2008

I had a similar problem on my 2000 XEDi. Found that the exhaust bracket that is bolted to the gearbox was cracked. Replaced it and all is fine. Could possible be somehing similar you are experiencing. No easy to detect, as it sits in an ackward spot, and is not easy to remove. You can only get to it from below, but the plastic tray under the engine is in the way. But you can inspect it by shining a light onto and hopefull are able to see if it is cracked.

ming · May 24, 2008

jaylewis29 said:
hi im new to all this so ill say hello and get on with it
ive recently bought a landrover freelander on a w(2000) plate nearly everything is fine, apart from when driving, @ 3000rpm on every gear change there is a vibration @ 3500rpm it gose away it feels like its coming from the middle (prop) but i know these things can be deciving, its bloody frustrating trying to get a smoothe ride, so the moral is any advice or help from any 1 would be greatfully appreciated thanks ......... jay

check fourebs solution. . . .un also get underneath un check all mounting parts on rear wiff a crow bar [for movement of mounting bushes ect] un best oh luck earthling

Buston · Jun 2, 2008

Have had the same problem on my 98 XEDi "TWICE"....rear diff mountings were the first problem but easily sorted the second was'nt so obvious at first (I was thinking the worst,IRD)

but the tyres had worn very unevenly on the rear ( Due to a seized Viscous coupling ) again fairly easy to change. I was running it on Good Year Wrangler All Terrains wich are quite nobbly. Changed to a more road biased tyre and hey presto...smooth running again ( for now!!). Good Luck

doobreydog · Jun 2, 2008

jaylewis29 said:
hi im new to all this so ill say hello and get on with it
ive recently bought a landrover freelander on a w(2000) plate nearly everything is fine, apart from when driving, @ 3000rpm on every gear change there is a vibration @ 3500rpm it gose away it feels like its coming from the middle (prop) but i know these things can be deciving, its bloody frustrating trying to get a smoothe ride, so the moral is any advice or help from any 1 would be greatfully appreciated thanks ......... jay

Sounds as if possible VCU mounting brackets loose...for some reason they put a very short bolt into these when new (pre 2001 only me thinks) and are often threaded when replacing...If you do remove replace with 35mm M8 (off top of shed so check it fits and about 10mm longer than original) or vcu bearing worn..check for excess play.

Could also pe front driveshaft worn

Pikey · Jun 2, 2008

If it needs a noo VCU give HB a shout she'll sell yer one of her Yarkursheere Puds to replace it with.

HybridGirl · Jun 2, 2008

redhand said:
If it needs a noo VCU give HB a shout she'll sell yer one of her Yarkursheere Puds to replace it with.

Aye. Yer cun ave one of me fantabulous Yarksheeeer Puddins fer a tenner.

Vibration

jaylewis29

New Member

chuts

New Member

faureb

Member

ming

SPACE TWOT

Buston

New Member

doobreydog

Active Member

Pikey

Dummy Ejection Facilitator..

HybridGirl

New Member

Similar threads