V8 Discovery 2 won't start means

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Checked fuses in engine bay F15, F14 & F13 all ok and passenger comp F23, F24, F26, F29 and F34.
Apart from fuel pump and starter solenoid all seems to be working and no errors. Hopefully 1 hour with Shims and his Nanocom will help.
 
What i was trying to say was that it might be a fusebox issue(bad contact within it) not a blown fuse cos a blown fuse from one of those you mentioned would have affected other things too
 
Thanks Sierrefery I agree with you, Now the systemematic task of working through the wiring diagramme with a multi meter and Shims Nanocom. I am sure that this will give me hours of entertainment . The only thing I don't underdstand is why the voltages reported on my scanner at the BCU were lower than what I measured at the cigar lighter?
 
Hi Guys.
I have diagnosed the fault using Shims Nanocom.
Was able to run fuel pump using test function.
The engine warning light is lit on dash ( Should this stay on if engine not started?)and ecu reports.
P1668 anti theft serial link fault signal too low once and too high 3 times.
Disabling imobiliser did not clear this.
I have got the bypass link ARM4956 will now research how to fit this.
Any advice Sierrafery?
 
Thanks for the advice guys. All alarm options had been disabled.
However I have now mhad a breakthrough. I am not certain if it is a permenant fix, but the car is running again!
I used the Nanocom to test everything and the only consistent fault was the serial link.
I restored all security settings to normal and tried to fault find further.
I have just had the windscreen fixed which stopped a water leak that was running down the Lhs A pillar and along a wiring harness through the connector. I dismantled this connector and found corrosion within the connector - see photo. I cleaned up the connector and gently filed the terminals( with the power off). I tested it and still same fault. I decided to start the car using the paper clip and switch on the fuel pump with the Nanocom. It was cold so I also put on the heater whilst I scrolled through the ECU and BCU pages - no faults found. I shut down the car, replace the relays and tried to restarted the car. It worked and ran fine!!
All I can think is that when wet, the corrosion gave a good contact, however as it started to dry out, the resistance went
20171109_214119.jpg
high on one or more of the terminal.
As far as the fix is concerned, cleaning the terminals will have improved the connection. The higher residual voltage of the battery may have then overcome any remaining poor contact. The proof of the pudding will be in the cold light of day tomorrow morning.
 
Fault reoccurred today. I started the car, drove for 2 mins, parked up for 3o mins without locking the car. Get back in ignition came as normal then would not crank.
Relocked car and retried - still no luck. Popped the starter relay out and started with paperclip. Car ran fine and will now start when ignition used. No faults recorded on ECU or BCU. Voltage at cigar lighter was 12.4V.
I have not given the corroded connector a thorough clean yet. Faulty relay?
 
I have now cleaned the corroded connector with contact cleaner and gteased it with electrical grease. Still working. Will try R3 swap if it fails again. Thanks for the support.
Other than this persistent fault my ACE is back working and currently have no other faults .
 
For the future, in places where water or moister can have bad effect use this http://www.nanoroad.co.uk/auto-coatings/4-nano-protech-electric.html it's the bee's knees in this area, treating both fuseboxes and exposed connectors with it can keep you troublefree, since i've discobered it few years ago i keep using it once a year on everything even in the ECUs and no problems caused by corrosion or bad contacts so far
 
Fault reoccurred today. I tried Sierrafery's suggestion of replacing starter relay with R3. No improvement. I jumped out the starter relay with my trusty paper clip and the engine ran fine. I pulled the fuel pump relay with the engine running and the engine died in 2 seconds. Stopped the car. Replaced all relays and tried to start it - no luck. Used paper clip ran car for 5 mins, moved it on my drive. Replaced all relays and now it starts fine. Using the diagnostics
Onto ECU P1668 = Anti-thrift alarm serial link fault drive cycle A occurred 2 times, signal too high fault is currently not present. What do you think is faulty?
 
ManxDisco said:
Fault reoccurred today. I tried Sierrafery's suggestion of replacing starter relay with R3. No improvement. I jumped out the starter relay with my trusty paper clip and the engine ran fine. I pulled the fuel pump relay with the engine running and the engine died in 2 seconds. Stopped the car. Replaced all relays and tried to start it - no luck. Used paper clip ran car for 5 mins, moved it on my drive. Replaced all relays and now it starts fine. Using the diagnostics
Onto ECU P1668 = Anti-thrift alarm serial link fault drive cycle A occurred 2 times, signal too high fault is currently not present. What do you think is faulty?
Click to expand...

That's the Passive Immob I think ... set by the main dealers ... only the drivers side opens ?...

Dragged this off of the web;
SYMPTOM VERIFICATION OF ACTIVATED PASSIVE IMMOBILIZATION

1. Unlock the vehicle and wait one minute.

2. With the ignition off, verify that the anti-theft alarm LED in the instrument pack blinks slowly.

3. Turn the ignition key to position "II" and verify the alarm LED is on continuously. This indicates an immobilized condition.

4. Check that Passive Immobilization is on by attempting to start the vehicle with the LED on continuously.

5. If the vehicle does not start, confirm that Passive Immobilization is turned on as follows:

^ Turn off ignition and remove the key.

^ Press the unlock button on the plip once.

^ Attempt to restart the vehicle within 30 seconds.

^ If the vehicle starts normally, Passive Immobilization is activated. The BCU must be replaced or reprogrammed by Land Rover after contacting the LRNA HelpLine.

hope this helps ...

Edited to add: http://www.landroversonly.com/forums/f40/fault-code-p1668-28431/
 
You must log in or register to reply here.

Similar threads

D
Discovery 1 300tdi immobiliser
Replies
1
Views
254
Stanleysteamer
Stanleysteamer
G
Anti Roll Bar disconnect
Replies
16
Views
453
Gingerbread
G
MAF Diver
Disco 2 Is my ACE leaking fluid at the actuator arm? New bushing?
Replies
9
Views
491
MJI
MJI
F
Disco 1 Immobiliser issues
Replies
11
Views
1K
discool
discool
loonyspoony
Disco 1 300TDI No Start
2 3
Replies
41
Views
2K
loonyspoony
loonyspoony
Back
Top