Unavailable door latches

flatlander · Aug 3, 2011

My Defender 90, 1985, needs two new door latches, lift-up handle type. None of the usual parts stockests can get hold of them - can anyone suggest where I might get them, or will I need to replace the doors. Photos attached (I hope).

Station House · Aug 3, 2011

What a total shag

Had a trawl for you, and yes (part MUC6979) appears to be no longer in production.

Think that leaves you trawling ebay, breakers yards etc.

They sometimes come up on ThePart.com - but can be expensive

What is actually wrong with them? Believe at one time a spring kit is avaialble if that's what's broken

wickford90 · Aug 3, 2011

flatlander said:
My Defender 90, 1985, needs two new door latches, lift-up handle type. None of the usual parts stockests can get hold of them - can anyone suggest where I might get them, or will I need to replace the doors. Photos attached (I hope).

I doubt very much if you will have to replace the doors, Have you tried the usual spares suppliers, Buckley bros, lrspares, paddocks, craddocks, look in a land rover mag.

wickford90 · Aug 3, 2011

flatlander said:
My Defender 90, 1985, needs two new door latches, lift-up handle type. None of the usual parts stockests can get hold of them - can anyone suggest where I might get them, or will I need to replace the doors. Photos attached (I hope).

look here.Land Rover spare parts and accessories | Landrover Series 1 and 2 Discovery Range Rover Freelander

flatlander · Aug 3, 2011

Thanks for your help, I have tried most of the main suppliers but will also try the others mentioned.

Not sure what's wrong, I have replaced the lock cylinder but the mechanism doesn't lock, even though the new cylinder pins lift.

I will try a thorough degrease, and as a last resort drill out the rivets and dismantle the thing, but don't really want to do this if there are no replacements available.

Simpler to leave the beast unlocked, with nothing stealable inside.

ZVDefender90 · Aug 3, 2011

Paddocks have these parts:
Part Number 395038 - Door Handle LH - Anti Burst
Part Number 395037 - Door Handle - RH Anti Burst & Defender Rear Safari Door

I have order these for my Series 3 doors but I am not 100% sure on the pin but it looks similar to the ones you have?

flatlander · Aug 3, 2011

Thanks ZV Defender. This looks so similar that it's worth a punt. I'll let the forum know if it works.

Cheers.

4x4tom · Aug 3, 2011

When you removed the lock did you take care not to loose the to ball bearings that should stay in the mech when you pulled the barrel? If they have gone walkabouts it wont lock anymore....

flatlander · Aug 3, 2011

4x4 Tom, I think you have answered the problem. I got the 90 just recently, and knew the door locks weren't working. When I stripped them there were no ball bearings, but I did not know enough to look for them!

Thanks, now I just have to find a new set of balls.....

munroe.frost · Aug 3, 2011

When I got mine the ball bearings were missing, If you find any can you post up where you found them please. I've looked for ages and found none.

Dave

Tazz070299 · Aug 4, 2011

ball bearings are easy enough to buy, all you need is the diameter of the originals.

Tazz

4x4tom · Aug 4, 2011

I had an old bearing that i bust open and they happened to be the correct size, give me a pm if you have trouble finding them.

flatlander · Aug 4, 2011

Thanks 4x4tom, I've sent a pm.

flatlander · Aug 17, 2011

My local locksmith has sorted out my missing balls (!) and the required diameter, for future reference, is 4.75mm.

GRATCH · Aug 17, 2011

That'll be 3/16" dia then

mickdj · Aug 17, 2011

i went to paddocks the other week for a set of barrels for these lock and when i fitted lost a bearing not noing about it, when id worked it out i ****ed about for ages id cut end of a 3/16 rivet and kept fileing abit off untill it work right.

Badger · Apr 9, 2012

Dragging an old thread up, does anyone have any idea how these barrels come out?

No hole to depress the pin as that part is housed within the unit itself with no way of gaining access to it without pulling it apart, unless there's another way. I've took the bolt out which sits in line to the rear of the barrel but that hasn't done anything.

I don't have the keys either

Boris113 · Apr 10, 2012

Badger said:
Dragging an old thread up, does anyone have any idea how these barrels come out?

No hole to depress the pin as that part is housed within the unit itself with no way of gaining access to it without pulling it apart, unless there's another way. I've took the bolt out which sits in line to the rear of the barrel but that hasn't done anything.

I don't have the keys either

You have a PM

Nothing-left · May 18, 2020

Boris113 said:
You have a PM

Hi,

many chance of letting me know how to do this too? move just painted and fitted new door on my 90 to find out I can’t get the lock out and don’t have keys either,

thanks

Discokids · May 24, 2020

Nothing-left said:
Hi,

many chance of letting me know how to do this too? move just painted and fitted new door on my 90 to find out I can’t get the lock out and don’t have keys either,

thanks

This is one of the most extreme thread resurrections I have ever seen!

Unavailable door latches

It's not broken!

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

It's not broken!

New Member

It's not broken!

Active Member

It's not broken!

New Member

New Member

Active Member

It's not broken!

It's not broken!

HUGE MEMBER

New Member

Well-Known Member

Well-Known Member

New Member

Well-Known Member

Similar threads