Says it’s made in same workshop as original and is oe spec.
I don’t see how this lobe won’t wear as the vacuum pump wheel isn’t exactly a fine surface.
I’ll get stripping it and measuring everything this weekend
Try again….
- Thread starter resto_d1
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
I don’t see how this lobe won’t wear as the vacuum pump wheel isn’t exactly a fine surface.
I’ll get stripping it and measuring everything this weekend
RAW111111
Well-Known Member
- Posts
- 255
- Location
- Nottingham
Have you seen the photo of the old vacuum pump from when I changed it? Not that surprised that the lobe is worn to be honest!Nasty wear on the camshaft lobe that powers vacuum pump. Thought “oh no that’ll cost”. 80 odd quid from turners!can’t complain about Land Rover parts costs.
Rich
I’m half tempted to get the machine shop to build the bottom end up and crack on with the welding. I’ve no idea of costs of this though and need to call them today when I get a sec. I’m excited to strip down it all down. I haven’t got bore mics and would do it using plastigage to work out tolerances. Might be worth leaving the bottom end to the pros.
You always worry that every single thing has been checked or done when putting it in someone else’s hands though!
You always worry that every single thing has been checked or done when putting it in someone else’s hands though!
- Posts
- 5,155
- Location
- South Bucks
Bit like my oil seal leak, after having the cam belt changed, I took it back and he says he put another new kit in, but it still leaks from the wading plug hole. Need to find someone who you know will do it properly.
I'm not good with removing cam belts.
Really is easy on 300 mate. Hardest bit is cracking off the dog nut
Haven’t started on engine yet but couldn’t resist a little tinkering. Really chasing a premium feel for the interior. I think it’s achievable.
First step is walnut then I’ll be adding more leather touches.
The walnut set I got was a little damaged but not too bad. Some bits had gone a bit milky in the clear. Others had cracked or scratched.
The walnut switch piece, the cherry on the cake, was first experiment to fix. The veneer is thin as hell and I did Nick it a couple times. I’ve used filler where I have which should darken as I coat.
The switch panel was missing the heated seat holes which I dremmeled in.
I’m not putting thick poly coating on it, I’ll use a couple of oils I think. Seems wrong to put lacquer on walnut!! You’re meant to enhance it, not hide it.
First step is walnut then I’ll be adding more leather touches.
The walnut set I got was a little damaged but not too bad. Some bits had gone a bit milky in the clear. Others had cracked or scratched.
The walnut switch piece, the cherry on the cake, was first experiment to fix. The veneer is thin as hell and I did Nick it a couple times. I’ve used filler where I have which should darken as I coat.
The switch panel was missing the heated seat holes which I dremmeled in.
I’m not putting thick poly coating on it, I’ll use a couple of oils I think. Seems wrong to put lacquer on walnut!! You’re meant to enhance it, not hide it.
was going well until I got to the dark patches. The veneer comes off with it.
I’ve ordered walnut burr veneer sheets and going to give it a whirl mate
- Posts
- 5,155
- Location
- South Bucks
How's it going
Good. Haven’t had a lot of time. Just been doing trim bits when I stop for a coffee! Hopefully I’ll get some more time soon. I need to get the bloody engine sent off but busy working to pay for said engine works
Had to weld some tv bracket bolts up for the pulley as the threads were tiny on it! Worked and that’s all that matters
CR bearings show scorch marks - assumed lack of oil/high miles. All look pretty similar to be honest.
Pistons and rods out then stopped to fit an overhead light in the shack as switch and wiring been in for ages!!
CR bearings show scorch marks - assumed lack of oil/high miles. All look pretty similar to be honest.
Pistons and rods out then stopped to fit an overhead light in the shack as switch and wiring been in for ages!!
RAW111111
Well-Known Member
- Posts
- 255
- Location
- Nottingham
Be interesting how much longer they'd have lasted wouldn't it. Looks like there's a bit of wear on them as you say.
Definitely. The head would’ve caused issues first I reckon but I’d bet those bearings had a good few k left in them!
- Posts
- 22,900
- Location
- In the next Glen
RAW111111
Well-Known Member
- Posts
- 255
- Location
- Nottingham
To be honest I wouldn't be sure that the cracks in the head would have been an issue any time soon. Heads on the M51d25 used in the P38 are renowned for cracking. I've had three different heads now to inspect and not had one without any cracks at all. One on mom's car at the moment had some small cracks when I had it pressure tested and skimmed 4 years and 30k miles ago (admittedly being a p38 it's spent at least one of those years not being started never mind driven). Comparatively the 300tdi doesn't really have a reputation for cracking that I'm aware of?
Rich
Bit more progress…
Dash out and a dig into one of my favourite areas. The ridiculous bottom corner of the windscreen. Believe it or not, I’ve got lucky here and was happy with what I found! I’ve left it soaking in deox gel
Sound deadening was wringing wet. A pillar footing looks alright. Bit of a nasty bit by the dash bracket but screwdriver didn’t go through it I still think I’ll chop it out as it will go at some point at the joint.
Dash out and a dig into one of my favourite areas. The ridiculous bottom corner of the windscreen. Believe it or not, I’ve got lucky here and was happy with what I found! I’ve left it soaking in deox gel
Sound deadening was wringing wet. A pillar footing looks alright. Bit of a nasty bit by the dash bracket but screwdriver didn’t go through it I still think I’ll chop it out as it will go at some point at the joint.
- Posts
- 5,155
- Location
- South Bucks
How's it going
