Try again….
- Thread starter resto_d1
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Cheers mate - already done in 4 way stretch just got to finish off some edges and the holes today
Have you still got that jap import?
- Posts
- 5,155
- Location
- South Bucks
Any updates
Hicap phill
Well-Known Member
- Posts
- 16,237
- Location
- Wiltshire
Bet he already has the welder out…
Not much! Headlining is in. Didn’t realise how saggy one of the rear nets was until refitted 
. Slowly ordering engine bits for a freshen up.
Welder isn’t out yet but fresh swan neck, tips and wire are all fitted.
Rear crossmember looks good apart from the top of it so may open it up and reseal with fresh metal.
. Slowly ordering engine bits for a freshen up. Welder isn’t out yet but fresh swan neck, tips and wire are all fitted.
Rear crossmember looks good apart from the top of it so may open it up and reseal with fresh metal.
- Posts
- 68,223
- Location
- The Wooly Witch
A good eyeball over the head for flow correction maybe ?
I keep changing my mind with ideas. I think I’ll just keep sorting the body out which is fairly inexpensive and I’ve also got things like bushes and an a frame fulcrum in my Landy box and save to completely do the engine and hit it in one.
Got a mechanical pump here ready to go to diesel bob plus mechanical injectors.
Would then send bottom end for honing and get a new turners head.
My other train of thought is, stick a head gasket on and give inspection like you say, stick new belts on and see how it goes!
Hicap phill
Well-Known Member
- Posts
- 16,237
- Location
- Wiltshire
That hole clips onto something to stop it rolling back up.Does anyone know what bit this hole was for? Was there a liner attachment available that clipped into it? If so I need it to finish it off
View attachment 292916
RAW111111
Well-Known Member
- Posts
- 255
- Location
- Nottingham
There’s a bit of elastic with a popper on the back of the seat to hold it rolled up.Does anyone know what bit this hole was for? Was there a liner attachment available that clipped into it? If so I need it to finish it off
View attachment 292916
Rich
Genius
Cheers. It feels so much cleaner.
San Miguel. Can’t drink peroni or Stella - both break my head into small pieces!
Ordered a ton of corroless and some thinners. Not sure what I’ll top coat stuff in. Wanted epoxy mastic but that seems to have gone silly prices. Got a couple sets of bearings and washers etc in stock. Think I’ll start on rear axle today in between house jobs and get the needle gun out.
So much better to have an idea of what I’m doing this time and also have the room and not worry etc. I can take my time and enjoy it all. The neighbours are sound and seems there won’t be tooooo much grinding and chopping anyway.
So much better to have an idea of what I’m doing this time and also have the room and not worry etc. I can take my time and enjoy it all. The neighbours are sound and seems there won’t be tooooo much grinding and chopping anyway.
- Posts
- 68,223
- Location
- The Wooly Witch
I always took wine and chocs around to apologise for the noise and mess ...
- Posts
- 5,155
- Location
- South Bucks
Still moving forward?
Nowt done yet - been busy with work etc. hopefully back end of the week I’ll be able to progress. Need to buy a gazebo too.
I did win an engine crane and have decided I’m going to repaint her in a flat colour - I do love the standard colour but every panel has damage or Ali corrosion on. I’m going to do the lot in epoxy primer then nisocoat, couple panels at a time. The bay will also be done once engines out and I can weld bulkhead spots
I did win an engine crane and have decided I’m going to repaint her in a flat colour - I do love the standard colour but every panel has damage or Ali corrosion on. I’m going to do the lot in epoxy primer then nisocoat, couple panels at a time. The bay will also be done once engines out and I can weld bulkhead spots
