Tracking.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
martynv8 said:
Wouldn't the diesel be even heavier on the front end?
Click to expand...

Diesel manual is 232 lbs lighter on rear end. Diesel auto 243 lbs lighter. 4.0 litre manual and auto are 221 lbs lighter at rear. And 4.6 is same as diesel auto at 243 lbs lighter on arse end. Kerb side weights include a full tank of fuel and a 75 kilo driver. So it would seem someone had his forklift in the wrong place. :D:D
 
Well like I said, I DONT KNOW, im not saying I know more about it I do not, just saying i had same thing on some cars over the years and that woz the tracking but don't know about the RR, will ask him when I take it in wot it is, in fact might pop in and ask him.:confused2:
 
Hairy said:
Well like I said, I DONT KNOW, im not saying I know more about it I do not, just saying i had same thing on some cars over the years and that woz the tracking but don't know about the RR, will ask him when I take it in wot it is, in fact might pop in and ask him.:confused2:
Click to expand...

And as i said it doesn't matter what vehicle it is, the symptoms i described are the same for all. Road camber can play a part but that usually makes the N/S tyre wear more than the O/S if the track is out. Not the other way round. If the N/S tyre is good but the O/S is worn on the inner shoulder and the tyres have been on for the same amount of time, i would be looking at camber angle on the O/S. That would be the ball joints worn, if he has the tooling get him to check the camber angles on the front axle. Camber should be zero. :);)
 
Well could be that, I don't have a clue, he just said 45 quid to sort that out it would take about an hour, bit more if things are rusted up solid, and been under it this morning to do gearbox oil and things are rusty.:D
 
Hairy said:
Well could be that, I don't have a clue, he just said 45 quid to sort that out it would take about an hour, bit more if things are rusted up solid, and been under it this morning to do gearbox oil and things are rusty.:D
Click to expand...

Moving the adjuster could be a problem then.
 
Hairy said:
Think he said that. :)
Click to expand...

Don't know what he uses, but sticking optical gauges on and checking track takes about ten minutes. Altering the track if it's out and the adjuster moves takes another ten to fifteen minutes. If the adjuster is seized you could be looking at up to a couple of hours. Then he may need to adjust drag link. If track is a long way out he needs to find out what has caused it.
 
On the MOT weighing system, mine was 122 Kilo's lighter at the rear last time.
They check axle weights here so fitting a Cummins to a Classic would be a big no no.
 
It is the tracking, just called in on way home from work, both tyres are scrubing the inside, didn't notice the n/s as it aint that bad:rolleyes: will see Friday if it feels better when its done. Thank you for your replys Gentlemen.:D:D:D:D:D:D:D:D:D:D:D
 
You must log in or register to reply here.

Similar threads

p38DH
P38A Diagnostic device
Replies
8
Views
1K
p38DH
p38DH
S
Brakes
Replies
17
Views
916
kermit_rr
kermit_rr
P38 guy
Amplifier/sub 12v line
2
Replies
27
Views
2K
kermit_rr
kermit_rr
P38 guy
Running p38 sub and amp on aftermarket head unit
Replies
9
Views
603
P38 guy
P38 guy
J
P38
Replies
4
Views
274
Grrrrrr
Grrrrrr
Back
Top