EeEk
Well-Known Member
- Posts
- 681
- Location
- Elgin, Scotland
aye its not always cheaper to DIY :hysterically_laughi
Too keen with the angle grinder
- Thread starter Snelly
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
xat44
Active Member
- Posts
- 474
- Location
- biggin on the bump
regarding how easy to change. just done my upper and lower ball joints. so had to remove the knuckle and it was a bitch on mine. big hammer and not a lot of room to swing it trying to break two tapers. used a fair bit of heat as well. dont think i would have got it off without damaging the ball joints.
good luck.
good luck.
Snelly
New Member
- Posts
- 45
- Location
- Lincolnshire
Im still looking for a suitable replacement knuckle. Probably have more luck on monday when places are open, but would of liked to of got it done tomorrow. Need it for work tuesday grrrr
Snelly
New Member
- Posts
- 45
- Location
- Lincolnshire
I have the top one loose, but bottom one being stubborn. Ive soaked it in penetrating oil and left it til the morning when i will resume my hammering
lorri789
Well-Known Member
- Posts
- 4,657
- Location
- West Stirlingshire
We had a thread about the stupid things we've all done. We're all guilty of summit.
Mickeyblueeyes
New Member
- Posts
- 47
- Location
- South Derbyshire
List of 'real' Haynes translations comes to mind haha
Haynes: One spanner rating (simple).
Translation: Your Mum could do this... so how did you manage to botch it up?
Lol
Don't worry I know someone who didn't think the oil light pressure switch mattered if it didn't work, next thing leg out of bed at 50mph on his 300tdi defender lol
Haynes: One spanner rating (simple).
Translation: Your Mum could do this... so how did you manage to botch it up?
Lol
Don't worry I know someone who didn't think the oil light pressure switch mattered if it didn't work, next thing leg out of bed at 50mph on his 300tdi defender lol
flat
Well-Known Member
- Posts
- 9,075
- Location
- Far away from you!!
or refit in reverse of removal basically means 'good luck getting that back together'
http://www.messybeast.com/dragonqueen/real-haynes.htm
Mickeyblueeyes
New Member
- Posts
- 47
- Location
- South Derbyshire
Or
Haynes: Refitting is the reverse sequence to removal.
Translation: But you swear in different places.
Haynes: Locate securing bolt.
Translation: Remember that worrying noise when you drove along the A38 last summer? That's where you'll find the securing bolt.
And (still laughing at this one)
Haynes: Apply moderate heat...
Translation: Placing your mouth near it and huffing isn't moderate heat.
Translation #2: Heat up until glowing red, if it still doesn't come undone use a hacksaw.
Translation #3: Unless you have a blast furnace, don't bother. Clamp with adjustable wrench then beat repeatedly with hammer.
Lol
Sorry Snelly
Haynes: Refitting is the reverse sequence to removal.
Translation: But you swear in different places.
Haynes: Locate securing bolt.
Translation: Remember that worrying noise when you drove along the A38 last summer? That's where you'll find the securing bolt.
And (still laughing at this one)
Haynes: Apply moderate heat...
Translation: Placing your mouth near it and huffing isn't moderate heat.
Translation #2: Heat up until glowing red, if it still doesn't come undone use a hacksaw.
Translation #3: Unless you have a blast furnace, don't bother. Clamp with adjustable wrench then beat repeatedly with hammer.
Lol
Sorry Snelly
