To buy or not to buy??

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Karlos28 said:
Well I bought it! Needed to get something soon and that was the cheapest for the spec level.

First and main issue, the exhaust is rubbing on the front prop-ird flange. Makes a right old racket! Hopefully get under it later and see what's a miss. Need to sort driver's door window regulator and maybe the Aircon needs a regas too.


I drove about 50 miles home on the m62 and M60, got back and checked the VCU temp, warm but perfectly touchable. OWU test pending..
Click to expand...
Looks like yer fallen int love with it already. Happy motoring. :)
 
Haha cheers, feel properly part of the club now!

I will do if I can sort this racket out! Engine/gearbox collapse is my guess but not sure where to look yet!?
 
Got both front door speakers working after a bit of a clean of the sockets and pi s on the connectors. Much better.

Driver's window is being held in place by a wedge of wood. New regulator needed. Tailgate door won't open, micro switch is clicking (even though the handle has snapped off as usual!) Nothing else happens. Rear window won't move in any way possible. Regulator looks fine, connections look fine. Rear wiper arm works and all central locking. If I try and out the window down with the interior switch, I can hear the relay clicking, so I'm guessing it's the motor. Are they replaceable individually or is it the full regulator job?
 
Found the source of the exhaust/prop interference... Front upper driver's side engine mount was basically not attached... The fitting on the engine block has one partially stripped hole, and the other looks ok. Both holes must have been damaged as the bolts wouldn't run down. New bolts, and managed to find one being broken to nab the engine mount off! All sorted now.

Just a 5 window regulators to change now!
 
Karlos28 said:
Parked up at work today and reversing into the space suggested VCU is a bit tight!
Click to expand...
Need to do the one wheel up test Karlos - some resistance on turning and particularly in reverse is to be expected. Mine does this, and the OWUT time is 45 seconds - and therefore acceptably within the published forum limits :)
 
Yeah, was thinking about it earlier.. I stall the thing that much in a straight line enough as I am so used to a diesel auto, and diesel manuals at work!

Will get the OWUT done and record timings. It'd be nice if I didn't need to spend £300 on a VCU.


Think I'm going to have a go at albrios tailgate handle repair, just need to source a lense for the number plate light. Also need a motor for the rear glass, it worked when I test drove it, but now it doesn't so can't get the back door open. Got the door card off, plug looks ok, regulator looks fine.. relay is clicking but no movement on the motor.
 
Awesome cheers Andy, will check them out!

It also has a hot idle issue.. it hunts from about 500rpm to about 1250rpm, almost stalling and some times it does. Oil light even flashes very faintly when Revs drop low. Had a quick Google and it seems to be some sort of IPCV (or some arrangement of other letters) which it attached to the manifold with 4 bolts and can get clogged with oily crap?
 
Karlos28 said:
Had a quick Google and it seems to be some sort of IPCV (or some arrangement of other letters) which it attached to the manifold with 4 bolts and can get clogged with oily crap?
Click to expand...
Idle Air Control Valve (IACV);).
They go sticky, so need to be cleaned with something like WD40.
 
One letter! Haha

It occurred to me earlier that whilst poking around I found a hose off the manifold.. (idle wasn't an issue on the way home from picking it up) I bet this is why!

New speakers are needed for the front. Still really tinny, after some searching, found that the cone is solid and doesn't move. Magnet must have detached.. to halfrauds!
 
Well I had the iacv off, cleaned, and functioned with ignition on/off and all seems to work well but I still get the almost cutting out when I come off power (clutch in). Interestingly the cam cover breather was off the manifold when I got it.. if I disconnect this again it all works well?
 
Karlos28 said:
if I disconnect this again it all works well?
Click to expand...
This can happen with an adaptive capable ECU. The ECU will learn to run, sometimes quite well, with an incorrect running condition, like a split pipe. The ECU adapts it's values to suit the incorrect condition, which it's designed to do. However if the incorrect condition is caused by a fault, which is subsequently fix, the ECU will need to re-learn the correct running environment. Some good code readers can reset the "adaptive values" but most can't. So all you can do is allow the ECU time to relearn the correct values.
 
Hopefully so! The flickering oil light concerns me slightly, but I notice the oil is like pi$$ and is overfull. Oil change pending (my drive is mega steep)...

Tried HDC today, works well!
 
You must log in or register to reply here.

Similar threads

G
Which head Gasket to buy
Replies
11
Views
458
NPG
NPG
J
High Mileage Freelander 2 - am I crazy or could this be a good buy?
Replies
3
Views
555
Nodge68
Nodge68
M
Looking to buy advice
Replies
3
Views
642
Mikey HO
M
Kerlaan
Freelander 1 Propshaft carrier bearings - how long to change them? [SOLVED]
Replies
6
Views
970
Kerlaan
Kerlaan
M
Freelander 1 VCU off for car how to test
Replies
2
Views
300
GrumpyGel
GrumpyGel
Back
Top