blue beasty
Leaks an prone to bits dropping off
- Posts
- 63,107
- Location
- Gloucestercotshirewolds
Temperature Gauge only works over 70mph!
- Thread starter LadyLandy90
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
zeaphod
Well-Known Member
- Posts
- 3,107
- Location
- Belfast, Norn Iron
I seemed to be viewing it in anything goes new glasses required lol
SpaceDawg
Active Member
- Posts
- 935
- Location
- Cowfold, West Sussex
Ok, drive it about normally and see if you get any heat out of the blower, if you do not and you get only a slight amount when your doing 70 in my experience its the thermostat. Mine never went over the 1st white bar on the temp gauge until I was going about 65-70mph then it would go up a little (just under half) with just a little heating.
Also, has it ever worked properly since the engine was changed? And if anyone here knows the resistance readings off the sender its likely you can test the system with a multimeter.
Also, has it ever worked properly since the engine was changed? And if anyone here knows the resistance readings off the sender its likely you can test the system with a multimeter.
LadyLandy90
New Member
- Posts
- 6
- Location
- Tonbridge Kent
Thank you, that's exactly what it does!
- Posts
- 11,023
- Location
- North of the Wall
What Defender 90 do you have? Mine's a 300Tdi.
On mine, this is the thermostat in it's housing at the front of the engine.
This is my stat, which was stuck open. You can see the gap
It doesn't take much of a gap to allow the water to flood through to the radiator, the water is then being continuously cooled. So, temp gauge doesn't go up until you are burning a lot of fuel, fast, for a long time. It's an easy job to change. Get the tools out, swap new one in, put tools away = 20 mins.
On mine, this is the thermostat in it's housing at the front of the engine.
This is my stat, which was stuck open. You can see the gap
It doesn't take much of a gap to allow the water to flood through to the radiator, the water is then being continuously cooled. So, temp gauge doesn't go up until you are burning a lot of fuel, fast, for a long time. It's an easy job to change. Get the tools out, swap new one in, put tools away = 20 mins.
Have you taken the bit of wire off the sender and shorted it to earth? (You can do this with or without the engine running)
If not, try that and you should get the needle to fully swing over to the very hot on the gauge.
If it doesn't, then you have a fault in the wiring!
Start with the simple stuff first ...
If not, try that and you should get the needle to fully swing over to the very hot on the gauge.
If it doesn't, then you have a fault in the wiring!
Start with the simple stuff first ...
LadyLandy90
New Member
- Posts
- 6
- Location
- Tonbridge Kent
My Hero! Thermostat replaced & all is now wellWhat Defender 90 do you have? Mine's a 300Tdi.
On mine, this is the thermostat in it's housing at the front of the engine.
This is my stat, which was stuck open. You can see the gap
It doesn't take much of a gap to allow the water to flood through to the radiator, the water is then being continuously cooled. So, temp gauge doesn't go up until you are burning a lot of fuel, fast, for a long time. It's an easy job to change. Get the tools out, swap new one in, put tools away = 20 mins.
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Excellent news, well done
- Posts
- 11,023
- Location
- North of the Wall
Pleased you got it sorted. Hopefully, you'll get some warm air outer of the heater now
Similar threads
